Voron-2-Mods Alternatives

Voron-2-Mods reviews and mentions

• Voron 2.4 stopped working
  1 project | /r/VORONDesign | 15 May 2023

  I found my drivers getting too hot for my liking (more a reliability concern long term) so I added some fans with this mod

• Serial Request for dancat #8752
  3 projects | /r/voroncorexy | 4 Jan 2023

  They are the standard trident parts, I only changed the front idlers to the ramalama ones (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers), used a Mantis toolhead (https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Long/Mantis_Dual_5015) and modified the AB drive lower STL's, the Idler lower STL's and the XY Joints STLS's to accommodate the linear rails. I had to do these modifications because my horizontal extrusions were 310mm and not the 320mm needed for a trident 200x200.

• THE FILTER Mod
  4 projects | /r/VORONDesign | 7 Dec 2022

  I was eyeing this to give myself a purge bucket and tidy up my wiring. https://github.com/Ramalama2/Voron-2-Mods/tree/main/Mandalaroseworks/BedPan

• How does one know what is the best configuration to build?
  7 projects | /r/VORONDesign | 16 Sep 2022

  I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.

• Voron Trident 300 Serial Request - rogerlz#2677
  6 projects | /r/voroncorexy | 24 Jul 2022

  Rama Idlers (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers)

• Serial request V24R 250 otrava#5261
  2 projects | /r/voroncorexy | 7 Jul 2022

  PCB mod is as Sanity writes. As for the gantry, it's this mod https://github.com/Ramalama2/Voron-2-Mods/tree/main/Misumi_RBPB5 And another mod is for Front idlers https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers

• Serial Request Trident 300 - Discord: disney7G#8271
  2 projects | /r/voroncorexy | 7 Mar 2022
• I get chatter from the the top idler unless I set the stepper at an angle.
  1 project | /r/VORONDesign | 17 Feb 2022
• Belt rubbing on a 2.4
  1 project | /r/VORONDesign | 31 Jan 2022

  I printed this mod and it's been great for my printer

• If your building an Voron. Definitely print these front idler mods. My stock ones were chewing through AB belts. Link in the comments
  1 project | /r/satisfyingprints | 28 Jan 2022
• A note from our sponsor - InfluxDB
  www.influxdata.com | 29 Apr 2024

  Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality. Learn more →