Voron-2-Mods
All my mods at one place (by Ramalama2)
Voron-2-Mods | TridentSkirtLights | |
---|---|---|
13 | 2 | |
366 | 12 | |
- | - | |
0.0 | 0.0 | |
9 months ago | over 1 year ago | |
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Voron-2-Mods
Posts with mentions or reviews of Voron-2-Mods.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-01-04.
-
Voron 2.4 stopped working
I found my drivers getting too hot for my liking (more a reliability concern long term) so I added some fans with this mod
-
Serial Request for dancat #8752
They are the standard trident parts, I only changed the front idlers to the ramalama ones (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers), used a Mantis toolhead (https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Long/Mantis_Dual_5015) and modified the AB drive lower STL's, the Idler lower STL's and the XY Joints STLS's to accommodate the linear rails. I had to do these modifications because my horizontal extrusions were 310mm and not the 320mm needed for a trident 200x200.
-
THE FILTER Mod
I was eyeing this to give myself a purge bucket and tidy up my wiring. https://github.com/Ramalama2/Voron-2-Mods/tree/main/Mandalaroseworks/BedPan
-
How does one know what is the best configuration to build?
I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.
-
Voron Trident 300 Serial Request - rogerlz#2677
Rama Idlers (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers)
-
Serial request V24R 250 otrava#5261
PCB mod is as Sanity writes. As for the gantry, it's this mod https://github.com/Ramalama2/Voron-2-Mods/tree/main/Misumi_RBPB5 And another mod is for Front idlers https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers
- Serial Request Trident 300 - Discord: disney7G#8271
- I get chatter from the the top idler unless I set the stepper at an angle.
-
Belt rubbing on a 2.4
I printed this mod and it's been great for my printer
- If your building an Voron. Definitely print these front idler mods. My stock ones were chewing through AB belts. Link in the comments
TridentSkirtLights
Posts with mentions or reviews of TridentSkirtLights.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-07-24.
-
Voron Trident 300 Serial Request - rogerlz#2677
Thank you! Yes, that was only open for the serial video haha :D Nothing special about the electronics compartment except that it is inverted (https://voronregistry.com/mods/loganfraser-tridentinvertedelectronics) and has the UTOC-1 next to the Raspberry PI. The wiring ducts are a poorly modified (split body, copy, align) version of this mod https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/ryandam/Cable_management_duct . And here are the Skirt LEDs: https://github.com/Gi7mo/TridentSkirtLights
What are some alternatives?
When comparing Voron-2-Mods and TridentSkirtLights you can also consider the following projects:
whopping_Voron_mods
Voron-Afterburner - VORON Afterburner Upgrade
LGX_Lite_Stealthburner_CW2_style_mount - LGX Lite extruder mount for the Voron Stealthburner.
Voron-2 - Voron 2 CoreXY 3D Printer design
VoronUsers - Voron Community mods
Stealthburner-Umbilical-mod
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
Voron-Hardware - Cool Hardware designed by the Voron Design group
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
Voron-2-Mods vs whopping_Voron_mods
TridentSkirtLights vs whopping_Voron_mods
Voron-2-Mods vs Voron-Afterburner
TridentSkirtLights vs LGX_Lite_Stealthburner_CW2_style_mount
Voron-2-Mods vs Voron-2
TridentSkirtLights vs VoronUsers
Voron-2-Mods vs Stealthburner-Umbilical-mod
Voron-2-Mods vs VoronUsers
Voron-2-Mods vs VoronUsers
Voron-2-Mods vs Voron-Hardware
Voron-2-Mods vs VoronUsers
Voron-2-Mods vs VoronUsers