Voron-2-Mods VS VoronUsers

I found my drivers getting too hot for my liking (more a reliability concern long term) so I added some fans with this mod

They are the standard trident parts, I only changed the front idlers to the ramalama ones (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers), used a Mantis toolhead (https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Long/Mantis_Dual_5015) and modified the AB drive lower STL's, the Idler lower STL's and the XY Joints STLS's to accommodate the linear rails. I had to do these modifications because my horizontal extrusions were 310mm and not the 320mm needed for a trident 200x200.

I was eyeing this to give myself a purge bucket and tidy up my wiring. https://github.com/Ramalama2/Voron-2-Mods/tree/main/Mandalaroseworks/BedPan

I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.

Rama Idlers (https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers)

PCB mod is as Sanity writes. As for the gantry, it's this mod https://github.com/Ramalama2/Voron-2-Mods/tree/main/Misumi_RBPB5 And another mod is for Front idlers https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers

I printed this mod and it's been great for my printer

You wouldn’t be the first one to switch over ;) https://github.com/nateb16/VoronUsers/tree/master/printer_mods/nateb16/THE_FILTER

If you are planning on using it with a Voron, you may want to look into The Filter. It seems like its probably a better design. If you are going to use it with another enclosed printer it probably doesn't matter.

I just installed “The Filter” and took out the nevermore and the 3 bed fans I had running for chamber temps. Running the filter with the dual fan and the two side pods with individual fans seems to heat chamber even faster. link to The Filter

I think the advantage of the nevermore (or the filter which is what I used) is that you get a decent improvement in chamber temp. But, you can also just do this with bed fans and no internal filter. If my bed filter eventually fails, I'm probably just going to punch a hole in the wall and vent things straight out to the garage. I'll then just have bed fans.

The filter by nateb16 - heats the enclosure way faster and filters the ABS smells. I say it's better than the Nevermore

I went straight to a Stealthburner+cw2, Canbus(SB2040)/umbilical and Voron Tap out of the box but those are optional. I also gotten ACM for the deck and bottom covers. Otherwise minor items were wiring duct and extra WAGO connectors to make 5v and 24v power rails for future expansion. IMO changing the z sensor and ACM is the mandatory ones followed by the duct. Also consider "The Filter" rather than the Nevermore The Filter