SaaSHub helps you find the best software and product alternatives Learn more →
EBB Alternatives
Similar projects and alternatives to EBB
-
InfluxDB
Power Real-Time Data Analytics at Scale. Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality.
-
Nevermore_Micro
Activated Carbon Filters. Bad smells or fumes, or complaints thereof, should not keep you from being a maker!
-
SaaSHub
SaaSHub - Software Alternatives and Reviews. SaaSHub helps you find the best software and product alternatives
-
Legacy-V0.1-style-tensioners
Alternative belt tension mechanism for Voron Legacy, based on the Voron V0.1.
NOTE:
The number of mentions on this list indicates mentions on common posts plus user suggested alternatives.
Hence, a higher number means a better EBB alternative or higher similarity.
EBB reviews and mentions
Posts with mentions or reviews of EBB.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-12-08.
-
Voron Legacy Serial Request - u/Deadbob1978
BTT SB2209 CAN toolhead board
-
Wiring between CR touch and ebb36
For the EBB: https://github.com/bigtreetech/EBB
-
TMC2240's have arrived!!!
I have the EBB2240 but I've been having the undervoltage problem every now and again: https://github.com/bigtreetech/EBB/issues/28 a bunch of other have too
-
EBB36/42 with 3 pin fan + tach wiring - does this look right? When the sense/pulse wire is added my FAN0(1) starts spinning at idle/cold.
I've logged an issue on BTT's repo to try and get some better (hopefully documented) information - https://github.com/bigtreetech/EBB/issues/48
-
EBB36 2-Wire PT1000?
I'm currently rebuilding my Voron V2.4 among others with CAN using a BTT EBB36:
-
input_shaper
You want one of these toolhead boards or similar. Definitely putting them on my next printer. Stepper driver for extruder, seperate MCU, accelerometer, fan outputs, led outputs, all wiring for the heater element and thermistor, and more. Only needs 2 data wires, plus power and ground. Fits in the footprint of a stepper motor.
- Question about Picobilical
-
The SB CAN Tool Board?
Flash newest possible firmware into all the hardware (!!! including U2C if you are using it !!!). There is help for compiling and flashing your own klipper image for EBB36. https://github.com/bigtreetech/EBB
-
Canbus my pico is being difficult.
Well I used the UART cable like in your guide with the same waveshare board I connected a blue wire to the low and a yellow high both 22 awg using the pinpout from here and I ran two 18 awg from psu directly to the other side of the molex using the same pinout image. Then connected blue to low on waveshare and yellow to waveshare . I have the 120ohm resistor on it's jumper position and at one time the uuid showed up of the tool head I placed that in the EBBCan.cfg and it was visible until I rebooted. I might try to reflash and terminate all wires again tomorrow evening after I get off to verify. If it won't work then, I'll assume something is wrong with the ebb36 board and return it. Try to get a replacement. I know they're getting proper voltage on cause everytime I turn it on the bl touch that's hooked up on the tool head performs the self check of the servo motor where the pin goes down and up again like three times like it says on the klipper man page
-
Mellow SHT36 Configuration
So if you are having difficulty with the sample configs or flashing instructions for that board you can likely also reference the BTT documentation.
-
A note from our sponsor - SaaSHub
www.saashub.com | 3 May 2024
Stats
Basic EBB repo stats
14
404
6.6
about 2 months ago
Popular Comparisons
Sponsored
SaaSHub - Software Alternatives and Reviews
SaaSHub helps you find the best software and product alternatives
www.saashub.com