EBB
By bigtreetech
Klicky-Probe
Microswitch probe with magnetic attachement, primarily aimed at CoreXY 3d printers (by jlas1)
EBB | Klicky-Probe | |
---|---|---|
14 | 69 | |
409 | 1,186 | |
- | - | |
6.6 | 5.0 | |
2 months ago | 18 days ago | |
- | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
EBB
Posts with mentions or reviews of EBB.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-12-08.
-
Voron Legacy Serial Request - u/Deadbob1978
BTT SB2209 CAN toolhead board
-
Wiring between CR touch and ebb36
For the EBB: https://github.com/bigtreetech/EBB
-
TMC2240's have arrived!!!
I have the EBB2240 but I've been having the undervoltage problem every now and again: https://github.com/bigtreetech/EBB/issues/28 a bunch of other have too
-
EBB36/42 with 3 pin fan + tach wiring - does this look right? When the sense/pulse wire is added my FAN0(1) starts spinning at idle/cold.
I've logged an issue on BTT's repo to try and get some better (hopefully documented) information - https://github.com/bigtreetech/EBB/issues/48
-
EBB36 2-Wire PT1000?
I'm currently rebuilding my Voron V2.4 among others with CAN using a BTT EBB36:
-
input_shaper
You want one of these toolhead boards or similar. Definitely putting them on my next printer. Stepper driver for extruder, seperate MCU, accelerometer, fan outputs, led outputs, all wiring for the heater element and thermistor, and more. Only needs 2 data wires, plus power and ground. Fits in the footprint of a stepper motor.
- Question about Picobilical
-
The SB CAN Tool Board?
Flash newest possible firmware into all the hardware (!!! including U2C if you are using it !!!). There is help for compiling and flashing your own klipper image for EBB36. https://github.com/bigtreetech/EBB
-
Canbus my pico is being difficult.
Well I used the UART cable like in your guide with the same waveshare board I connected a blue wire to the low and a yellow high both 22 awg using the pinpout from here and I ran two 18 awg from psu directly to the other side of the molex using the same pinout image. Then connected blue to low on waveshare and yellow to waveshare . I have the 120ohm resistor on it's jumper position and at one time the uuid showed up of the tool head I placed that in the EBBCan.cfg and it was visible until I rebooted. I might try to reflash and terminate all wires again tomorrow evening after I get off to verify. If it won't work then, I'll assume something is wrong with the ebb36 board and return it. Try to get a replacement. I know they're getting proper voltage on cause everytime I turn it on the bl touch that's hooked up on the tool head performs the self check of the servo motor where the pin goes down and up again like three times like it says on the klipper man page
-
Mellow SHT36 Configuration
So if you are having difficulty with the sample configs or flashing instructions for that board you can likely also reference the BTT documentation.
Klicky-Probe
Posts with mentions or reviews of Klicky-Probe.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-12-08.
- Voron Legacy Serial Request - u/Deadbob1978
- Voron 2.4 klicky probe issue
-
Using a servo on Creality 4.2.7
I used this github as a guide to get my servo to work on my BTT SKR Mini E3 V3 https://github.com/jlas1/Klicky-Probe/tree/main/Printers/Voron/Switchwire then you have to mess with the pulse width value until it works right, lots of trial and error
-
Controlling servo with E3V2 stock board
So you want to use this one? https://github.com/jlas1/Klicky-Probe/tree/main/Printers/Voron/Switchwire
-
Another Perfect First Layer
GitHub, there's the install for all the different variants (klicky, unklicky and the ng variants), with macros, boms and instructions https://github.com/jlas1/Klicky-Probe
-
Klicky probe config
I just went through the same build and I just included the klicky files as specified here, edited the variables file and that was it
- Unpopular opinion: ABL is trash
- Z-offset is constantly changing after every quad_gantry_level (v2.4)
- Ender 6 with SKR mini e3v3 and klipper ABL options
-
Motor to open V2.4 Doors
The official Klicky setup for the Switchwire uses one as well
What are some alternatives?
When comparing EBB and Klicky-Probe you can also consider the following projects:
zippy-klipper_config - Zippy Klipper Config
Euclid_Probe - Euclid probe, a magnetically coupled Z Probe
voron_canbus
klipper_z_calibration - Klipper plugin for self-calibrating z-offset
Nevermore_Micro - Activated Carbon Filters. Bad smells or fumes, or complaints thereof, should not keep you from being a maker!
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
WLED - Control WS2812B and many more types of digital RGB LEDs with an ESP8266 or ESP32 over WiFi!
SlideSwipe
VoronUsers - Voron Community mods
whopping_Voron_mods
Quickdraw_Probe - A Magnetically Coupled, Removable, Z Probe and Dock System
EBB vs zippy-klipper_config
Klicky-Probe vs Euclid_Probe
EBB vs voron_canbus
Klicky-Probe vs klipper_z_calibration
EBB vs Nevermore_Micro
Klicky-Probe vs VoronUsers
EBB vs WLED
Klicky-Probe vs SlideSwipe
EBB vs VoronUsers
Klicky-Probe vs whopping_Voron_mods
Klicky-Probe vs VoronUsers
Klicky-Probe vs Quickdraw_Probe