EBB
VoronUsers
EBB | VoronUsers | |
---|---|---|
14 | 347 | |
409 | 2,863 | |
- | 1.2% | |
6.6 | 8.8 | |
2 months ago | 8 days ago | |
OpenSCAD | ||
- | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
EBB
-
Voron Legacy Serial Request - u/Deadbob1978
BTT SB2209 CAN toolhead board
-
Wiring between CR touch and ebb36
For the EBB: https://github.com/bigtreetech/EBB
-
TMC2240's have arrived!!!
I have the EBB2240 but I've been having the undervoltage problem every now and again: https://github.com/bigtreetech/EBB/issues/28 a bunch of other have too
-
EBB36/42 with 3 pin fan + tach wiring - does this look right? When the sense/pulse wire is added my FAN0(1) starts spinning at idle/cold.
I've logged an issue on BTT's repo to try and get some better (hopefully documented) information - https://github.com/bigtreetech/EBB/issues/48
-
EBB36 2-Wire PT1000?
I'm currently rebuilding my Voron V2.4 among others with CAN using a BTT EBB36:
-
input_shaper
You want one of these toolhead boards or similar. Definitely putting them on my next printer. Stepper driver for extruder, seperate MCU, accelerometer, fan outputs, led outputs, all wiring for the heater element and thermistor, and more. Only needs 2 data wires, plus power and ground. Fits in the footprint of a stepper motor.
- Question about Picobilical
-
The SB CAN Tool Board?
Flash newest possible firmware into all the hardware (!!! including U2C if you are using it !!!). There is help for compiling and flashing your own klipper image for EBB36. https://github.com/bigtreetech/EBB
-
Canbus my pico is being difficult.
Well I used the UART cable like in your guide with the same waveshare board I connected a blue wire to the low and a yellow high both 22 awg using the pinpout from here and I ran two 18 awg from psu directly to the other side of the molex using the same pinout image. Then connected blue to low on waveshare and yellow to waveshare . I have the 120ohm resistor on it's jumper position and at one time the uuid showed up of the tool head I placed that in the EBBCan.cfg and it was visible until I rebooted. I might try to reflash and terminate all wires again tomorrow evening after I get off to verify. If it won't work then, I'll assume something is wrong with the ebb36 board and return it. Try to get a replacement. I know they're getting proper voltage on cause everytime I turn it on the bl touch that's hooked up on the tool head performs the self check of the servo motor where the pin goes down and up again like three times like it says on the klipper man page
-
Mellow SHT36 Configuration
So if you are having difficulty with the sample configs or flashing instructions for that board you can likely also reference the BTT documentation.
VoronUsers
-
Serial Request - Trident 300 - Discord: orangetruth
270º Clamping Hinges
-
Re-did my Rook Legacy to Rook 2020. Lowered the Z and used 2020 extrusions for the frame to make it super stable. Threw in Klicky probe and CPAP cooling too 😁
Hotend is a Triangle Labs CHC Pro. Extruder setup is a mixture of a couple 😅 -mod of Mantis Toolhead to mount on MGN9C
-
Serial request | V0.2 | Discord: Hr_Ravn#7480
Stealth skirts by Maverick
-
Wire guides which I'm using to help with cable management on my 2.4 build
Those are a duct remix of this design, it is not yet posted since I need to install my wires to make sure no changes are needed. It will probably be uploaded in the next week.
-
Serial Request Voron Trident
I'm running a Chainflex umbilical cable + a beacon probe USB cable along the prebowden. I'm thinking about running the Bowden guide to help, I'm not pinching anything when I home the printer, but I'm looking to keep everything up and out of the way. https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Galvanic/Bowden_Tube_Guide
-
Finally reached 60C with my scavenged solution for bed fans. ASA is smooth!
Here is a good cfg to automate the fans
-
config issues
basically copied and pasted from here: VoronUsers/bedfans.cfg at master · VoronDesign/VoronUsers · GitHub with printer specific info bellow
-
Remix of Hartk1213's Voron2.4 GE5C Z Joint (available on Printables and TeamFDM)
Why don't you submit this to the vetted mods repository? https://github.com/voronDesign/voronusers
-
Silly question. How do you open bottom panel?
I swapped to these magnetic bottom panels and they are awesome!
-
Voron Trident 3D Printer Review - My experience with the Fysect Kit | igor'sLAB
I noticed that you mentioned being annoyed by the cable management (or lack of it) in the kit, which I think is probably not uncommon with many kits with some exceptions (LDO looks nice). That bothered me also, so I'm also working on something to help with cable management, which may also work with the Trident (a remix of these cable ducts).
What are some alternatives?
zippy-klipper_config - Zippy Klipper Config
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
voron_canbus
Klicky-Probe - Microswitch probe with magnetic attachement, primarily aimed at CoreXY 3d printers
Nevermore_Micro - Activated Carbon Filters. Bad smells or fumes, or complaints thereof, should not keep you from being a maker!
Sherpa_Mini-Extruder - A smaller version of the sherpa extruder, direct and bowden supported
WLED - Control WS2812B and many more types of digital RGB LEDs with an ESP8266 or ESP32 over WiFi!
whopping_Voron_mods
klipper - Klipper is a 3d-printer firmware
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
Voron-Afterburner - VORON Afterburner Upgrade
LGX_Lite_Stealthburner_CW2_style_mount - LGX Lite extruder mount for the Voron Stealthburner.