Klipper Alternatives
-
Klipper_SKR_PRO_TMC2209_Ender5
Klipper configuration for my SKR PRo v1.1 based Ender 5
-
Cura
3D printer / slicing GUI built on top of the Uranium framework
-
Scout
Get performance insights in less than 4 minutes. Scout APM uses tracing logic that ties bottlenecks to source code so you know the exact line of code causing performance issues and can get back to building a great product faster.
-
KlipperScreen
GUI for Klipper
-
Marlin
Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine. (by smith3d)
-
FluiddPI
FluiddPi - A Pi image with Klipper, Moonraker, Fluidd and Web Camera support pre-installed.
Posts
-
Voron style Bed/Probe offset
https://github.com/KevinOConnor/klipper/blob/master/config/kit-voron2-250mm.cfg like this?
-
Install on a Ender 3 V2 with BLtouch / help / install together
Have you tried fluiddpi? It has a really simple install to get you up and running quickly. Once you have that installed you can find a good config from the klipper docs for your ender 3 v2 (https://github.com/KevinOConnor/klipper/blob/master/config/printer-creality-ender3-v2-2020.cfg).
- Help with Klipper settings for Anycubic Mega S/X
-
Board Change To Skr 14 And Tmc2209 For Ender3
Yes that's right you can't use my config file for an Ender 3 pro with the original mainboard. The difference are the pin mappings between the SKR and the original board. If you take a look in the Klipper config folder on Github you can find many example config files for example for the Ender with the board from 2018 or with a newer board from 2020: https://github.com/KevinOConnor/klipper/tree/master/config
-
Klipper and Cura usability fail or do I miss the logic?
BTW, did you do the bed leveling / paper test pre-heated? According to the documentation it's recommended to do this at room temperature. I wonder if the observed difference is caused by doing the calibration with heated components.
-
Ender 5 Pro Klipper Issues with Starting Print
At first glance there's some other obvious issues that pop out. Look over the Klipper Gcode to see what is and isn't supported. I see commands like M75, M420 and M900 in the start G-code that aren't supported by Klipper and I don't see a Macro for any of them. Unless I missed it, the only one you have is for G29. For setting the fade with M420, just use the cfg settings and remove that.
-
Ender 5 Pro Printer Config
Have you had a look at the Ender 5 default config?
That config is wrong in regard to the board it is compiled for, and I'm not sure about the other settings. The Ender 3 Pro config here is good, just the directions and home locations have to change. That's what I did for my Ender 5 pro with the 4.2.2. I posted mine below
-
Hotend Moving to far
You should also have a look at this document, and get rid of step_distance anyway. it's being phased out in favor of rotation_distance.https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md
-
Printer keeps showing “move out of range”. Help appreciated.
Those distances are calculated with "enhanced delta calibration" which I haven't done currently, will run it now. https://github.com/KevinOConnor/klipper/blob/master/docs/Delta_Calibrate.md#enhanced-delta-calibration
-
Bmg extruder tuning.
How so? 415 steps of a 1.8° stepper feeds 1mm of filament out of a BMG. Calculations to derive rotational distance from steps per mm are provided in the Klipper documentation. Unless you have a gear ratio value entered, all you need is the calculated value, and you should only be using gear ratio if the stepper itself has a gear box (since the steps on the motor are not 1:1 with the output shaft. The extruder gearing itself is accounted for in the steps/mm to rotational distance calculation.).
You can tune the extruder using the measure and trim procedure. https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md#calibrating-rotation_distance-on-extruders
-
G2 and G3 arc movements?
https://github.com/KevinOConnor/klipper/blob/master/docs/Config_Reference.md#gcode_arcs
-
Getting error when trying to Make for an SKR Mini E3 v2
To make this a more valuable post, here is the information I got from the Klipper Github for the SKR Mini E3 v2 board here
-
Some really basic usability questions before I switch
You could power it that way, it's only a 5v trace on AUX-1, but there are a few factors to take into account; The Pi requires at least 2.5 amps to run properly, so you will be putting strain on a 5v converter that isn't designed for that. The TFT screen should compatible with Klipper and you will be able to use it as a RepRap full graphics display (Klipper doesn't support color LCDs on the MCU, but you can connect any HDMI touch screen to the Pi and use KlipperScreen to control the printer from that) Link to a thread on how to make it work (scroll down) https://github.com/KevinOConnor/klipper/issues/2231. The other issue is that if you power your Pi down with the printer, you will need to turn that on before sending any files to it.
Stats
KevinOConnor/klipper is an open source project licensed under GNU General Public License v3.0 only which is an OSI approved license.