zippy-klipper_config
EBB
zippy-klipper_config | EBB | |
---|---|---|
252 | 14 | |
343 | 404 | |
- | - | |
6.9 | 6.6 | |
6 days ago | about 2 months ago | |
Shell | ||
GNU General Public License v3.0 only | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
zippy-klipper_config
- How to prevent auto shutoff?
-
Is there a way to calculate max Z height?
See my guide for more detail
-
Seeking a Reliable Firmware Solution for Artillery Sidewinder X1 3D Printer (V86 and V87 issue)
i’ve adapted macros and some things from this repo https://github.com/rootiest/zippy-klipper_config
-
Just went Klipper on my 8-bit Ender 5 Pro
try this out https://github.com/rootiest/zippy-klipper_config/blob/master/guides/GUIDE-axis_limits.md
-
Installation guide/best installation instructions
klipp tut
-
FIGHTING FOR DAYS
I'd suggest giving my guide a read
-
Imperial March ringtone using the beeper of the mini12864 LCD Display
Here is my beeper tune collection if anyone is interested
-
Pressure advance pattern method help
Check out my guide
-
Installed Klipper, Start/End G-Code
Try my guide for simple, basic start/end print macros.
-
Controlling Neopixel at logo and nozzle separately from dashboard.
Check out this simplified config I made
EBB
-
Voron Legacy Serial Request - u/Deadbob1978
BTT SB2209 CAN toolhead board
-
Wiring between CR touch and ebb36
For the EBB: https://github.com/bigtreetech/EBB
-
TMC2240's have arrived!!!
I have the EBB2240 but I've been having the undervoltage problem every now and again: https://github.com/bigtreetech/EBB/issues/28 a bunch of other have too
-
EBB36/42 with 3 pin fan + tach wiring - does this look right? When the sense/pulse wire is added my FAN0(1) starts spinning at idle/cold.
I've logged an issue on BTT's repo to try and get some better (hopefully documented) information - https://github.com/bigtreetech/EBB/issues/48
-
EBB36 2-Wire PT1000?
I'm currently rebuilding my Voron V2.4 among others with CAN using a BTT EBB36:
-
input_shaper
You want one of these toolhead boards or similar. Definitely putting them on my next printer. Stepper driver for extruder, seperate MCU, accelerometer, fan outputs, led outputs, all wiring for the heater element and thermistor, and more. Only needs 2 data wires, plus power and ground. Fits in the footprint of a stepper motor.
- Question about Picobilical
-
The SB CAN Tool Board?
Flash newest possible firmware into all the hardware (!!! including U2C if you are using it !!!). There is help for compiling and flashing your own klipper image for EBB36. https://github.com/bigtreetech/EBB
-
Canbus my pico is being difficult.
Well I used the UART cable like in your guide with the same waveshare board I connected a blue wire to the low and a yellow high both 22 awg using the pinpout from here and I ran two 18 awg from psu directly to the other side of the molex using the same pinout image. Then connected blue to low on waveshare and yellow to waveshare . I have the 120ohm resistor on it's jumper position and at one time the uuid showed up of the tool head I placed that in the EBBCan.cfg and it was visible until I rebooted. I might try to reflash and terminate all wires again tomorrow evening after I get off to verify. If it won't work then, I'll assume something is wrong with the ebb36 board and return it. Try to get a replacement. I know they're getting proper voltage on cause everytime I turn it on the bl touch that's hooked up on the tool head performs the self check of the servo motor where the pin goes down and up again like three times like it says on the klipper man page
-
Mellow SHT36 Configuration
So if you are having difficulty with the sample configs or flashing instructions for that board you can likely also reference the BTT documentation.
What are some alternatives?
klippain - Generic Klipper configuration for 3D printers
voron_canbus
klipper - Klipper is a 3d-printer firmware
Nevermore_Micro - Activated Carbon Filters. Bad smells or fumes, or complaints thereof, should not keep you from being a maker!
kiauh - Klipper Installation And Update Helper
WLED - Control WS2812B and many more types of digital RGB LEDs with an ESP8266 or ESP32 over WiFi!
klipper_z_calibration - Klipper plugin for self-calibrating z-offset
VoronUsers - Voron Community mods
mainsail - Mainsail is the popular web interface for managing and controlling 3D printers with Klipper.
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
print_area_bed_mesh - Create bed mesh for print area only
klipper-voron-V2 - Generic Klipper configuration for a CoreXY printers like Voron v2.4, Trident, V0 and co