Special_Configurations
BIGTREETECH-SKR-mini-E3
Special_Configurations | BIGTREETECH-SKR-mini-E3 | |
---|---|---|
101 | 579 | |
172 | 1,931 | |
- | - | |
7.2 | 1.6 | |
18 days ago | 28 days ago | |
C | C++ | |
GNU Lesser General Public License v3.0 only | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Special_Configurations
-
Mesh colour coding — all blue?
Have a look at https://github.com/mriscoc/Ender3V2S1/wiki/How-to-update-the-display I had an Ender 3 V2 with a TJC display that needs a special compile to display the numbers. You can find the specially compiled firmware bin's here: https://github.com/mriscoc/Special_Configurations/releases/tag/tjc
-
Sprite Extruder Calibration - Homing issues
PID tuning - Using Pronterface and the M303 command, I get "PID Autotune failed! Bad Heater id". Searching on this one I found the man himself mention " using an MPC version of the firmware, so there is no PID for the extruder". The firmware I used is an MPC version - so I need to run the MPC autotune instead. I cant run it as I can't home the head.
-
HELP! I got the SKR Mini E3 V3.0 and it says, "No Printer Connected!"
-I am using the Touchscreen with the included cables. I have the singular pin with the touchscreen's 5 pin connection on the left if the drivers are at the top of the board. - The broad rate set to 115200 -I am using a CR touch with the 5 pin connector in the 5 pin CR touch thingy -I am using this firmware, " Ender3V2-SKRME3V3-BLTUBL-T13-LA-MPC-20230809.bin" on this page https://github.com/mriscoc/Special_Configurations/releases I have not edited it because I have no clue how to do that
-
Firmware Flash issues
As well as a T13 version (https://github.com/mriscoc/Special_Configurations/releases/download/T13/Ender3V2-422-BLTUBL-T13-MPC-20230812.bin)
-
First layer disaster on my heavily modded E3v2
See here: https://github.com/mriscoc/Special_Configurations
-
You would think my printer would be dialed in by now.
I basically went through the Marlin config file for my printer line by line to change it how I like. You might also want to check out Professional firmware, he as many precompiled configs, and the source code. I think his has a 10 minute hotend timeout in it.
- Anyone install a pro hot end for this printer from Creality and be able to adjust temps to above 260?
- Downgrading s1 pro touchscreen to s1 knob screen
-
Need assistance identifying an issue
You're welcome :-) Mriscoc has a special configuration version of the firmware with linear advance enabled, https://github.com/mriscoc/Special_Configurations/releases/tag/LinearAdvance
-
Sprite Pro Extruder
I used mriscoc T13 be sure to follow the directions.
BIGTREETECH-SKR-mini-E3
- How do I fix this? I’ve tried everything. I installed an skr mini v3.0 and reflashed using their own bltouch precompiled firmware and nothing seems to work.
- BTT skr mini e3 v3 and orange pi zero 3 UART
-
Build his own firmware?
Last week I ugraded the mainboard to a BTT SKR mini E3 v3.0, and I just used the "firmware-USB.bin" from the GitHub page to flash that board, and I updated the pin names on the printer.cfg for my printer using the example on that same GitHub page. Everything is working well, the printer in producing good parts like it did before.
-
BTT SKR MINI 3.0 V3 + Marlin 2.1.2.1 on Ender 3 V2- fan wiring?
I went with this following the findings in this thread https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/658
-
Can't get CR touch, SKR Mini 3 V3.0 and Ender 3 Pro working. Help?
Disconnect 2 wires and hook it up to the Z-stop. Will probe, but it hovers about 25mm off the bed even when the z axis is brought all the way to 0. It will not go to negative values. Tried both the BLtouch and BLtouch-for-z-homing firmwares from here(https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin) but no luck
-
Le Potato and a BTT Mini SKR e3 v3 - Via UART
At this point I've narrowed it down to the Klipper firmware being sent over to the Mini and after it boots. Looking at BTT's github, it is included in Klipper now. So I used the build scripts there through KIAUH. Set up the information to send it over USB and it flashes without error. I tried with Serial USART1 PA10/PA9. From the printer.cfg
-
SKR Mini E3 V3 Ender 3 issues "no printer attached" and "system: no system"
at some point, I was also trying to update the firmware. I have a BL touch installed at the same time so I tried to use the V3.0 Marlin firmware (https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/blob/master/firmware/V3.0/Marlin/firmware-ender3-bltouch.bin). I have no idea if it ever updated the firmware as there was never anything indicating it was installing. I assume I put it on a microSD, and plug it into the motherboard right?
-
Help - Cr touch / SKR mini e3
I recently made my first upgrade on my ender-3, a Bigtreetech SKR mini e3 v3. I also bought the official Creality CR touch and installed it onto my printer. I plugged the cable into the adequate spot on the board and unplugged the cable from the Z endstop switch. I then downloaded the firmware (firmware-ender3-bltouch-for-z-homing.bin) from this page: "https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin" and uploaded it to my printer.
-
SKR Mini E3 v3.0 cannot flash
Pre-compiled firmware. (GH)
- Uncompiled SKR Mini E3V3 firmware
What are some alternatives?
Ender3V2S1 - This is optimized firmware for Ender3 V2/S1 3D printers.
SKR-2
MRiscoCProUI - This is optimized firmware for Voxelab Aquila & Ender3 V2/S1 3D printers.
klipper - Klipper is a 3d-printer firmware
mriscoc_Special_Configurations - In this repository there are the configuration files for several Marlin firmware features
BIGTREETECH-SKR-E3-Turbo
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
Configurations - Configurations for Marlin Firmware