BIGTREETECH-SKR-mini-E3
Marlin
Our great sponsors
BIGTREETECH-SKR-mini-E3 | Marlin | |
---|---|---|
579 | 877 | |
1,926 | 2,142 | |
- | - | |
1.9 | 0.0 | |
19 days ago | 5 months ago | |
C++ | C++ | |
- | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
BIGTREETECH-SKR-mini-E3
- How do I fix this? I’ve tried everything. I installed an skr mini v3.0 and reflashed using their own bltouch precompiled firmware and nothing seems to work.
- BTT skr mini e3 v3 and orange pi zero 3 UART
-
Build his own firmware?
Last week I ugraded the mainboard to a BTT SKR mini E3 v3.0, and I just used the "firmware-USB.bin" from the GitHub page to flash that board, and I updated the pin names on the printer.cfg for my printer using the example on that same GitHub page. Everything is working well, the printer in producing good parts like it did before.
-
BTT SKR MINI 3.0 V3 + Marlin 2.1.2.1 on Ender 3 V2- fan wiring?
I went with this following the findings in this thread https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/658
-
Can't get CR touch, SKR Mini 3 V3.0 and Ender 3 Pro working. Help?
Disconnect 2 wires and hook it up to the Z-stop. Will probe, but it hovers about 25mm off the bed even when the z axis is brought all the way to 0. It will not go to negative values. Tried both the BLtouch and BLtouch-for-z-homing firmwares from here(https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin) but no luck
-
Le Potato and a BTT Mini SKR e3 v3 - Via UART
At this point I've narrowed it down to the Klipper firmware being sent over to the Mini and after it boots. Looking at BTT's github, it is included in Klipper now. So I used the build scripts there through KIAUH. Set up the information to send it over USB and it flashes without error. I tried with Serial USART1 PA10/PA9. From the printer.cfg
-
SKR Mini E3 V3 Ender 3 issues "no printer attached" and "system: no system"
at some point, I was also trying to update the firmware. I have a BL touch installed at the same time so I tried to use the V3.0 Marlin firmware (https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/blob/master/firmware/V3.0/Marlin/firmware-ender3-bltouch.bin). I have no idea if it ever updated the firmware as there was never anything indicating it was installing. I assume I put it on a microSD, and plug it into the motherboard right?
-
Help - Cr touch / SKR mini e3
I recently made my first upgrade on my ender-3, a Bigtreetech SKR mini e3 v3. I also bought the official Creality CR touch and installed it onto my printer. I plugged the cable into the adequate spot on the board and unplugged the cable from the Z endstop switch. I then downloaded the firmware (firmware-ender3-bltouch-for-z-homing.bin) from this page: "https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin" and uploaded it to my printer.
-
SKR Mini E3 v3.0 cannot flash
Pre-compiled firmware. (GH)
- Uncompiled SKR Mini E3V3 firmware
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
What are some alternatives?
SKR-2
klipper - Klipper is a 3d-printer firmware
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
BIGTREETECH-SKR-E3-Turbo
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
Configurations - Configurations for Marlin Firmware
VoronUsers - Voron Community mods
MKS-Robin-Nano-V3.X - Robin nano V3 is an upgraded version of Robin Nano V2.0. The upgrade changes are quite large, including upgrading the MCU to the M4 core, and adding support for USB disk.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.