SV06-Fully-Open-Source VS everything-sovol-sv06

The A8's were responsible for a few housefires due to not having thermal runaway activated in the firmware, there are much much better printers available these days, one printer that is built the same as this but is based on the Prusa MK3 is the Sovol SV-06 and is a very good machine https://sovol3d.com/products/sovol-sv06-direct-drive-3d-printer

And even then, there are plenty of clones with comparable (and even slightly better) features for less than half the price.

Hey they have models here https://github.com/Sovol3d/SV06-Fully-Open-Source

You print the replacement part on a different printer, order it directly on the aftermarket, purchase it from the manufacturer, or have it print over a print service, as the entire assembly has been published by sovol. https://github.com/Sovol3d/SV06-Fully-Open-Source

The files provided from Sovol are replacement models for the parts on the printer that you could 3d print or source elsewhere from what I understand https://github.com/Sovol3d/SV06-Fully-Open-Source . The One-Stop Shop https://github.com/bassamanator/Sovol-SV06-firmware/tree/master provides some updated klipper (custom firmware) configs that seem to work well on the sv06 and that same person is trying to gather info on the electronic parts of the machine as well so we can replace the parts as needed if something breaks and don't need to wait on Sovol to reply to source a replacement https://github.com/bassamanator/everything-sovol-sv06 . I personally would love to contribute to the teardown but this is my first 3d printer and I am not nearly knowledgeable enough to begin tearing this apart fully. I likely will to grease the bearings but mine seem to have avoided the issue that has plagued numerous others and will try to document things then.

No need to take measurements Sovol have open sourced the parts and provided STL’s, you can find them here.

My friend, your machine can't handle those speeds. Here are some of my prints: https://github.com/bassamanator/everything-sovol-sv06/blob/39477b317da7dac40efbb3a844a3fb36dead922d/images/prints/README.md. You can try to reduce the `max print speed`, start off by limiting it to 60-70mm/s (match the other profile's speed). I hope you've made other adjustments to the `printer settings` as well so that it works with marlin.

You can get a raspberry pi zero 2 w for $15 bucks from any of the authorized retailers. I just bought one the other day for a mobile retropi I’m putting together. They have them in stock now. I run it on a pi 4 but I’ve read about a bunch of people here on Reddit who run klipper on a pi zero and have no issues. klipper install guide. This guide is pretty good for walking you through the setup process.

https://github.com/bassamanator/everything-sovol-sv06 SV06 here, might browse a bit for the 01 Pro.

You'll find the essentials here.

There is this site someone else in the community made https://sv06.blakadder.com/ and there is also the klipper github repo https://github.com/bassamanator/Sovol-SV06-firmware. The same user of the klipper repo also maintains a parts repo too https://github.com/bassamanator/everything-sovol-sv06 but the site also seems to have the same info

You can find specs here: https://github.com/bassamanator/everything-sovol-sv06

If you are not a tinkerer, I would suggest you get rid of this printer, because it will act as a thorn in your sides. On the other hand, if this is truly your hobby, you can expect to get prints such as these. I'll put up my sub $300 SV06 with severe x-twist against a more than $1000 MK4 any day!

great resource for info on sv06

Designing this part? You can find the link to the official CAD models for this printer at the bottom of this repo, might help the design process.