KlipperWrt
Marlin
KlipperWrt | Marlin | |
---|---|---|
7 | 877 | |
168 | 2,142 | |
- | - | |
0.0 | 0.0 | |
over 1 year ago | 6 months ago | |
Shell | C++ | |
- | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
KlipperWrt
-
Trying to get klipper onto creality wifi box
Hey guys, I've been following this tutorial for converting a creality wifi box to run klipper: https://github.com/ihrapsa/KlipperWrt
- Creality Ender 3 v2 Neo modification and upgrade guide
-
Klipper on the CR-10 Smart Pro
On a Laptop, log into the Printers Wifi (It will be named CXSWBox-12345678ABCDEF or similar), the password is "12345678". You will get an IP address via DHCP. The Wifi Boards web interface is reachable at 10.10.10.254 with username "admin" and password "admin". Go to Administration > Upload Firmware. Choose one one of the -factory images at https://github.com/ihrapsa/KlipperWrt/tree/main/Firmware/OpenWrt_snapshot, depending if you want to run fluidd or mainsail (Comparison is here: https://www.youtube.com/watch?v=BHVVcjtWTyA). Upload the image, you will get a message "Not a valid firmware". Go to http://10.10.10.254/adm/system_command.shtml and enter mv /var/tmpFW /media/mmcblk0p1/cxsw_update.tar.bz2 and for the next command reboot. Then wait for a KlipperWrt Wifi to show up. Connect to it, use the static IP 192.168.1.23 with netmask 255.255.255.0. The web interface is available at 192.168.1.1:81.
-
Klipper/Mainsail on android phone
I recall that Android phones are unreliable for Klipper with all of their built in power saving features that will interrupt prints. Any device that runs Linux should be able to run Klipper. A VM on a Mac or PC should be able to do it as long as you can reliably forward the virtual serial port. Running on a router is possible with KlipperWRT. https://github.com/ihrapsa/KlipperWrt
-
Running klipper on a 256mb ram device?
Instructions from Iona Rapsa's Github - https://github.com/ihrapsa/KlipperWrt
-
https://github.com/mriscoc/Marlin_Ender3v2/releases/latest
I followed this guide https://github.com/ihrapsa/KlipperWrt (used the openwrt image compiled by ihrapsa).
-
Installing upgrades right away or setting it up stock first?
I bought an Ender 3 v2 for my son as a birthday a couple of weeks ago, it came with the Creality cloud box (as a free gift). The cloud box was promptly flashed to OpenWrt and Klipper installed using guidance from https://github.com/ihrapsa/KlipperWrt.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
What are some alternatives?
KlipperScreen - GUI for Klipper
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
OpenWrt-Rpi - Raspberry Pi & NanoPi R2S/R4S & G-Dock & x86 OpenWrt Compile Project. (Based on Github Action / Daily Update)
klipper - Klipper is a 3d-printer firmware
OctoWrt - A guide to install Octoprint on the Creality WiFi Box or similar OpenWrt devices
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
klipper-web-control-docker - Klipper with Moonraker shipped with Fluidd and/or Mainsail
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
klipper-prusa-mk3s - Structured Klipper config for Prusa MK3s 3D printer
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
nanopi-openwrt - Openwrt for Nanopi R1S R2S R4S R5S 香橙派 R1 Plus 固件编译 纯净版与大杂烩
VoronUsers - Voron Community mods