Marlin
DGUS-reloaded-Klipper-config | Marlin | |
---|---|---|
11 | 7 | |
42 | 27 | |
- | - | |
0.0 | 9.9 | |
over 2 years ago | over 2 years ago | |
C++ | ||
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
DGUS-reloaded-Klipper-config
- Flash Ender 5 to install Klipper
-
Sonic Pad with CR10s pro v1
I found https://github.com/Desuuuu/DGUS-reloaded-Klipper-config/blob/master/base/creality-cr10spro.cfg Does anyone know if this would work for my v1 pro?
-
CR10s Pro v1 OctoPrint / Klipper BLTouch issues
I found This like that matches my setup and updated my printer.cfg so the sensor pin is mapped to PD3 pulled up.
- Need Firmware Please! CR10S Pro V1
-
CR-10S PRO (customized with BLTouch and Hemera). Should I move to Klipper from Marlin?
Maybe this one?
-
Ayyyy, it's here! Going to set it up tomorrow
10s pro Klipper config can be found here https://github.com/Desuuuu/DGUS-reloaded-Klipper-config
-
Firmware for CR10s Pro V2
This is the cfg file from desuuu that I tried: https://github.com/Desuuuu/DGUS-reloaded-Klipper-config/blob/master/base/creality-cr10sprov2.cfg Had to comment out the last section. I guess it is related to the touch screen that desuuu made to work by forking klipper. I'm hesitant to move away from mainstream bc it could get stale. But then again I didn't spend enough time on it, maybe it's the way to go! https://www.reddit.com/r/CR10/comments/qkjkqd/cr10s_pro_v2_klipper_config_file_with_oem_touch/ https://www.reddit.com/r/CR10/comments/ibckmm/klipper_with_support_for_the_cr10s_pro_touchscreen/
-
Help setting up PA
I have used desuu config file as a start-point https://github.com/Desuuuu/DGUS-reloaded-Klipper-config I had to tweak it a bit to make bed leveling works correctly as klipper has changed how it handles the probe offset since it was originally released (i had to subtract my offsets from the max probe points in order to avoid out of boundaries errors since i have a huge offses on x due to hero me fan ducts).
-
I want to try and Prusa-fy my Ender 5 Plus. Has anyone done something like this?
Configuration for the stock Creality board for Klipper: https://github.com/Desuuuu/DGUS-reloaded-Klipper-config/blob/master/base/creality-ender5plus.cfg
-
Having difficulty configuring bltouch (cr-10s Pro v1)
i already tried to use just bl_touch config from cr-10s pro v2
Marlin
-
Tiny Machines firmware question marks … why? EEPROM reset after update. Z offset set. Ideas?
Marlin FW (precompiled binaries): github.com/Desuuuu/Marlin/releases DWIN Screen Files: github.com/Desuuuu/DGUS-reloaded/releases Screen Instructions: github.com/Desuuuu/DGUS-reloaded/wiki/Flashing-the-firmware There are also config files if you want to compile that fork of Marlin: github.com/Desuuuu/Marlin
-
CR10S V2 Pro over running X & Y Axis
If you complied the firmware, and are using the stock board, I suggest that you check your conifguration.h against one from a similar (or same printer) to make sure that the bed size and endstop configs are correctly set (for example this one for the Desuuuu firmware https://github.com/Desuuuu/Marlin/blob/master/Marlin/Configuration.h). It may be simpler though to just try a pre-compiled fw like Tinymachines (make sure you get the BL Touch version) if you are using the stock board.
-
Factory firmware source code
For people who don't want to replace the whole LCD screen, this fork should work with the stock screen. I haven't tested it myself though. You also need to flash firmware to the screen in addition to the board.
- Cr-10s pro v2 with marlin 2.0 Z keeps moving
-
which firmware you use?
This year I started using an adapted version of the latest Marlin firmware (https://github.com/Desuuuu/Marlin). The touch screen works a lot better. I started printing and after a while still got the M999 error, carefully pulling the BLTouch probe somehow fixes this issue and I'm now able to use Simplify 3D, no idea if its related to slicer though since that doesn't make sense...
What are some alternatives?
KlipperScreen - GUI for Klipper
Marlin-Ender-5-Plus - Modified Marlin for Creality Ender 5 Plus (Released by Creality) for use with BTT hardware suite. Includes BLTouch offsets for popular hotend configurations.
klipper - Klipper is a 3d-printer firmware. Modified to work with DWIN T5UID1 touchscreens.
DGUS-reloaded-Klipper - DWIN T5UID1 touchscreen firmware for 3D printers running Klipper.
DGUS-reloaded - DWIN T5UID1 touchscreen firmware for 3D printers running Marlin.
Marlin - Optimized firmware for RepRap 3D printers based on the Arduino platform.
klipper-prusa-mk3s - Structured Klipper config for Prusa MK3s 3D printer
Marlin-2-0-x-Anycubic-i3-MEGA-S - Marlin 2.0.x Version for Anycubic i3 MEGA M/S/P/X/CHIRON and 4MAX with Anycubic TFT or the "new" DGUS Clone TFT - Now also with BLTouch!
klipper - Klipper is a 3d-printer firmware
DGUS-reloaded-config