Special_Configurations
Marlin
Special_Configurations | Marlin | |
---|---|---|
101 | 877 | |
172 | 2,142 | |
- | - | |
7.2 | 0.0 | |
18 days ago | 6 months ago | |
C | C++ | |
GNU Lesser General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Special_Configurations
-
Mesh colour coding — all blue?
Have a look at https://github.com/mriscoc/Ender3V2S1/wiki/How-to-update-the-display I had an Ender 3 V2 with a TJC display that needs a special compile to display the numbers. You can find the specially compiled firmware bin's here: https://github.com/mriscoc/Special_Configurations/releases/tag/tjc
-
Sprite Extruder Calibration - Homing issues
PID tuning - Using Pronterface and the M303 command, I get "PID Autotune failed! Bad Heater id". Searching on this one I found the man himself mention " using an MPC version of the firmware, so there is no PID for the extruder". The firmware I used is an MPC version - so I need to run the MPC autotune instead. I cant run it as I can't home the head.
-
HELP! I got the SKR Mini E3 V3.0 and it says, "No Printer Connected!"
-I am using the Touchscreen with the included cables. I have the singular pin with the touchscreen's 5 pin connection on the left if the drivers are at the top of the board. - The broad rate set to 115200 -I am using a CR touch with the 5 pin connector in the 5 pin CR touch thingy -I am using this firmware, " Ender3V2-SKRME3V3-BLTUBL-T13-LA-MPC-20230809.bin" on this page https://github.com/mriscoc/Special_Configurations/releases I have not edited it because I have no clue how to do that
-
Firmware Flash issues
As well as a T13 version (https://github.com/mriscoc/Special_Configurations/releases/download/T13/Ender3V2-422-BLTUBL-T13-MPC-20230812.bin)
-
First layer disaster on my heavily modded E3v2
See here: https://github.com/mriscoc/Special_Configurations
-
You would think my printer would be dialed in by now.
I basically went through the Marlin config file for my printer line by line to change it how I like. You might also want to check out Professional firmware, he as many precompiled configs, and the source code. I think his has a 10 minute hotend timeout in it.
- Anyone install a pro hot end for this printer from Creality and be able to adjust temps to above 260?
- Downgrading s1 pro touchscreen to s1 knob screen
-
Need assistance identifying an issue
You're welcome :-) Mriscoc has a special configuration version of the firmware with linear advance enabled, https://github.com/mriscoc/Special_Configurations/releases/tag/LinearAdvance
-
Sprite Pro Extruder
I used mriscoc T13 be sure to follow the directions.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
What are some alternatives?
Ender3V2S1 - This is optimized firmware for Ender3 V2/S1 3D printers.
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
MRiscoCProUI - This is optimized firmware for Voxelab Aquila & Ender3 V2/S1 3D printers.
klipper - Klipper is a 3d-printer firmware
mriscoc_Special_Configurations - In this repository there are the configuration files for several Marlin firmware features
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
VoronUsers - Voron Community mods