OctoPrint-FirmwareUpdater
Marlin_Ender3v2
Our great sponsors
OctoPrint-FirmwareUpdater | Marlin_Ender3v2 | |
---|---|---|
37 | 102 | |
344 | 12 | |
0.6% | - | |
3.0 | 9.9 | |
3 months ago | about 2 years ago | |
Python | C++ | |
GNU Affero General Public License v3.0 | GNU General Public License v3.0 or later |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
OctoPrint-FirmwareUpdater
-
So apparently I have to prove that my build plate is in fact pei coated ffs.
After reading some more seems like you CAN do it, but I was either too scared or didn't know about it in Mid-2021
-
Hi, I’m getting these uneven walls. It is the same diameter in each layer but each layer seems to be different from the next. Does anyone know what the problem is / have suggestions of any guides to follow to fix it?
Firmware Updater Useful for flashing firmware to printer without having to use sd card. Frees up an sd card for me
-
SKR V1.4 Turbo: update firmware w/out SD card?
I have 2 skr 1.4 turbo boards and before I switched to klipper I always updated my firmware using the firmware updater plug in for octoprint. On the github page it guided you through setup for that board family. https://plugins.octoprint.org/plugins/firmwareupdater/
-
*SOLVED* I am trying to use Firmware Updater after following install instructions for marlinbft. It seems to not be recognizing that I have the marlin-binary-protocol package installed. I am still getting "Python marlin-binary-protocol package is not installed" under the prerequisite status area.
I followed the install instructions from this link. I installed the python 3 compatible version of heat shrink.
-
How to update firmware to install CR touch?
Method 3 (Through Octopi) - I installed Anaconda to download the firmware updater for Octopi found here (https://plugins.octoprint.org/plugins/firmwareupdater/) but cannot install it through the command line. I get "python setup.py egg_info did not run successfully.". Tried upgrading pip to no avail.
-
S1 Help
if you have an Raspberry pi you can try https://plugins.octoprint.org/plugins/firmwareupdater/
-
Question about flashing firmware
I'm not sure if this OctoPrint plug-in works with the neptune 2 but it's worth a shot. https://plugins.octoprint.org/plugins/firmwareupdater/
- M600 Filament Swap now possible with the Neptune 3 Pro Firmware v1.1.5
-
Anyway to update firmware on E5 pro without and SD card?
You need a plugin called Firmware Updater.
-
Broke my SD Card reader any way I can still flash firmware using my octoprint?
Only if you already have Binary File Trainsfer setting enabled in Marlin. So you might be stuck since that's not normally enabled. But when it is enabled, it does work. I only update via octoprint anymore. https://github.com/OctoPrint/OctoPrint-FirmwareUpdater/blob/master/doc/marlinbft.md
Marlin_Ender3v2
-
ender 3v2 upgraded to sprite pro hitting dual screw gantry
From what I'm reading, mriscoc's firmware appears to be a bit more polished and offers even more features than Jyers. Have a look at their page - https://github.com/mriscoc/Marlin_Ender3v2/releases/latest From what I'm reading you can change the bed dimensions via gcode command and also in the advanced settings menu. I'm going to try this route despite having already downloaded all the software to compile my own jyers firmware..
-
Installation and Configuring for an Ender 3 S1
Download the bin file from here https://github.com/mriscoc/Marlin_Ender3v2/releases/latest.
-
Anybody know whats up with my 3dtouch? Just installed
By any chances are you using the Jyers firmware? Because that firmware works horrible with a lot of probes. Try the Professional Firmware, I never had a probe crashing problem with that one.
-
Why does my z offset keep changing?
Once you tram the bed, are you doing a mesh? I use UBL (Unified Bed Leveling) to do a 15x15 mesh that takes approximately 225 points of readings. If you are using Jyers firmware, which I highly recommend) or Professional firmware by mriscoc, both rimwares based on Marlin but are more rich in features than the base Marlin firmware, you can view the mesh on your display and see where the high/low spots are. The mesh can be saved to your EEPROM and used without having to redo the leveling process all the time. This is, of course, providing that your bed is not shifting and you wait for the bed to cool down before removing the prints so it doesn't mesh of the leveling. I am not sure about the Professional firmware (because I don't use that one) but I do know the Jyers firmware has a bunch of precompiled .bin files for all the boards and for many different configurations.
-
EEPROM and detecting of SD card not working correctly after upgrading to 2.4.7 motherboard
https://github.com/Jyers/Marlin/releases or https://github.com/mriscoc/Marlin_Ender3v2/releases
-
Octprint Levelling report vs UBL on printer
I am using a modified Jyers firmware from here: https://github.com/mriscoc/Marlin_Ender3v2
- Micro-Swiss direct drive install.
- Ungraded the bed leveling springs.
-
How do you save your Z offset settings?
i use https://github.com/mriscoc/Marlin_Ender3v2 and i am very happy with it
- CR-Touch - Mesh values are never saved correctly. Bed leveled but the values change after it homes/creates a new mesh.
What are some alternatives?
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint-APCUPC - An OctoPrint plugin for Raspbian to communicate with an APC UPC via serial
Ender3V2S1 - This is optimized firmware for Ender3 V2/S1 3D printers.
pivpn - The Simplest VPN installer, designed for Raspberry Pi
OctoPrint-FixCBDFirmware - Fixes communication with a broken firmware making its rounds that identifies as "CBD make it"
KlipperWrt - A guide to install Klipper with fluidd, Mainsail or Duet-Web-Control and webcam stream in OpenWrt. Mainly created around the Creality Wi-Fi box but any OpenWrt running device with similar specs will work just fine.
obico-server - Obico is a community-built, open-source smart 3D printing platform used by makers, enthusiasts, and tinkerers around the world.
klipper - Klipper is a 3d-printer firmware
OctoPrint-Resource-Monitor - An OctoPrint plugin to view current CPU and RAM usage
Configurations - Configurations for Marlin Firmware