Mini-AfterSherpa
VoronUsers
Our great sponsors
Mini-AfterSherpa | VoronUsers | |
---|---|---|
22 | 347 | |
273 | 2,850 | |
2.6% | 2.1% | |
0.0 | 8.8 | |
12 months ago | 29 days ago | |
OpenSCAD | ||
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Mini-AfterSherpa
-
Start/baseline config for mini-after-sherpa and sherpa mini motor/extruder?
Does anyone have a mini-after-sherpa with a phaetus dragonfly 55W heater hotend config?
-
Kingroon Halfwire Build: Mini-AfterSherpa (4010 or 3010 radial side/part-cool fans?)
I printed a mini aftersherpa from the github and it says everything is 3010 and 3007 fans. There's also many different remixes, mods, adaptations, etc. of the mini-after-sherpa hotend fan-shroud thing...
-
Is there an alternative toolhead design for v0.1 dragon sf ?
There's this one which is popular but pretty much the same as stock just with the top cut off. https://github.com/PrintersForAnts/Mini-AfterSherpa
-
Voron 0.1 Mods
If you're dead set on changing things up, the two (relatively) minor mods I'd suggest are the Mini-AfterSherpa toolhead and ZeroPanels panel clips. These will save you from dealing with the hassle of assembling a Mini-AfterBurner (my least favorite thing about V0.1), and inserting a million captive nuts, respectively.
-
V0.1 Serial Request : GrantsAusto#3657
I used the mount from https://github.com/PrintersForAnts/Mini-AfterSherpa. It requires 5V, then the gpios on the pi. I ended up going with an MGN9C and mini sherpa. The weight seemed to cause a drop but didn't test after the MGN9C upgrade
-
Serial Request - Voron 0.1 - Hemmar #8145
Sherpa Mini Extruder from Fabreeko with 8GT motor and Mini Aftersherpa. I found this easier to service than the mini afterburner
-
Micron+ ProMaxUltra™ - Serial Request - aTinyShellScript#3121
MiniAfterSherpa Toolhead with Revo Micro
-
Voron 0.1 - MGN9 - Carriage
I'm not entirely sure I understand your question but https://github.com/PrintersForAnts/Mini-AfterSherpa might be the answer
-
Am I missing something? Mosquito doesn’t seem to fit mini afterburner - using repo mini afterburner tool head files
In my opinion the Mini AB is terrible. I have the mosquito running with a Sherpa Mini extruder and cowling of my own design. But the mini after sherpa works ok. If you can't find another cowling that works, I could modify mine so it fits the larger mosquito. There are other designs out there like the V0VO
-
Serial Request // V0 // iammuffinman225#4921
I did the AfterSherpa mod with a standard V6 and mini-Sherpa because:
VoronUsers
-
Serial Request - Trident 300 - Discord: orangetruth
270º Clamping Hinges
-
Re-did my Rook Legacy to Rook 2020. Lowered the Z and used 2020 extrusions for the frame to make it super stable. Threw in Klicky probe and CPAP cooling too 😁
Hotend is a Triangle Labs CHC Pro. Extruder setup is a mixture of a couple 😅 -mod of Mantis Toolhead to mount on MGN9C
-
Serial request | V0.2 | Discord: Hr_Ravn#7480
Stealth skirts by Maverick
-
Wire guides which I'm using to help with cable management on my 2.4 build
Those are a duct remix of this design, it is not yet posted since I need to install my wires to make sure no changes are needed. It will probably be uploaded in the next week.
-
Serial Request Voron Trident
I'm running a Chainflex umbilical cable + a beacon probe USB cable along the prebowden. I'm thinking about running the Bowden guide to help, I'm not pinching anything when I home the printer, but I'm looking to keep everything up and out of the way. https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Galvanic/Bowden_Tube_Guide
-
Finally reached 60C with my scavenged solution for bed fans. ASA is smooth!
Here is a good cfg to automate the fans
-
config issues
basically copied and pasted from here: VoronUsers/bedfans.cfg at master · VoronDesign/VoronUsers · GitHub with printer specific info bellow
-
Remix of Hartk1213's Voron2.4 GE5C Z Joint (available on Printables and TeamFDM)
Why don't you submit this to the vetted mods repository? https://github.com/voronDesign/voronusers
-
Silly question. How do you open bottom panel?
I swapped to these magnetic bottom panels and they are awesome!
-
Voron Trident 3D Printer Review - My experience with the Fysect Kit | igor'sLAB
I noticed that you mentioned being annoyed by the cable management (or lack of it) in the kit, which I think is probably not uncommon with many kits with some exceptions (LDO looks nice). That bothered me also, so I'm also working on something to help with cable management, which may also work with the Trident (a remix of these cable ducts).
What are some alternatives?
Sherpa_Mini-Extruder - A smaller version of the sherpa extruder, direct and bowden supported
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
VOV0-toolhead-voron-Zero
Klicky-Probe - Microswitch probe with magnetic attachement, primarily aimed at CoreXY 3d printers
BoxZero - Simplify, strengthen, and seal your V0/T0/ X0 by ditching the tophat and moving to a full-box frame.
Sherpa-BLOCKhead - Hotend shroud for Voron0.1 and MiniSherpa
whopping_Voron_mods
klipper - Klipper is a 3d-printer firmware
double-dragon - Double Dragon: world's smallest IDEX 3D printer. Mod your Voron 0 or build one fresh!
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.