Marlin-BTT-RRF-E3
BIGTREETECH-SKR-mini-E3
Marlin-BTT-RRF-E3 | BIGTREETECH-SKR-mini-E3 | |
---|---|---|
1 | 579 | |
0 | 1,931 | |
- | - | |
0.0 | 1.6 | |
over 2 years ago | about 1 month ago | |
C++ | C++ | |
- | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Marlin-BTT-RRF-E3
BIGTREETECH-SKR-mini-E3
- How do I fix this? I’ve tried everything. I installed an skr mini v3.0 and reflashed using their own bltouch precompiled firmware and nothing seems to work.
- BTT skr mini e3 v3 and orange pi zero 3 UART
-
Build his own firmware?
Last week I ugraded the mainboard to a BTT SKR mini E3 v3.0, and I just used the "firmware-USB.bin" from the GitHub page to flash that board, and I updated the pin names on the printer.cfg for my printer using the example on that same GitHub page. Everything is working well, the printer in producing good parts like it did before.
-
BTT SKR MINI 3.0 V3 + Marlin 2.1.2.1 on Ender 3 V2- fan wiring?
I went with this following the findings in this thread https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/658
-
Can't get CR touch, SKR Mini 3 V3.0 and Ender 3 Pro working. Help?
Disconnect 2 wires and hook it up to the Z-stop. Will probe, but it hovers about 25mm off the bed even when the z axis is brought all the way to 0. It will not go to negative values. Tried both the BLtouch and BLtouch-for-z-homing firmwares from here(https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin) but no luck
-
Le Potato and a BTT Mini SKR e3 v3 - Via UART
At this point I've narrowed it down to the Klipper firmware being sent over to the Mini and after it boots. Looking at BTT's github, it is included in Klipper now. So I used the build scripts there through KIAUH. Set up the information to send it over USB and it flashes without error. I tried with Serial USART1 PA10/PA9. From the printer.cfg
-
SKR Mini E3 V3 Ender 3 issues "no printer attached" and "system: no system"
at some point, I was also trying to update the firmware. I have a BL touch installed at the same time so I tried to use the V3.0 Marlin firmware (https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/blob/master/firmware/V3.0/Marlin/firmware-ender3-bltouch.bin). I have no idea if it ever updated the firmware as there was never anything indicating it was installing. I assume I put it on a microSD, and plug it into the motherboard right?
-
Help - Cr touch / SKR mini e3
I recently made my first upgrade on my ender-3, a Bigtreetech SKR mini e3 v3. I also bought the official Creality CR touch and installed it onto my printer. I plugged the cable into the adequate spot on the board and unplugged the cable from the Z endstop switch. I then downloaded the firmware (firmware-ender3-bltouch-for-z-homing.bin) from this page: "https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Marlin" and uploaded it to my printer.
-
SKR Mini E3 v3.0 cannot flash
Pre-compiled firmware. (GH)
- Uncompiled SKR Mini E3V3 firmware
What are some alternatives?
SKR-2
klipper - Klipper is a 3d-printer firmware
BIGTREETECH-SKR-E3-Turbo
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
Configurations - Configurations for Marlin Firmware
MKS-Robin-Nano-V3.X - Robin nano V3 is an upgraded version of Robin Nano V2.0. The upgrade changes are quite large, including upgrading the MCU to the M4 core, and adding support for USB disk.
Marlin-2.0.x-SKR-Mini-E3-v1.2 - SKR MINI E3 v1.2 board Marlin 2.0 firmware for an Ender 3 Pro w/BLtouch (Standard mount)
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
platformio-vscode-ide - PlatformIO IDE for VSCode: The next generation integrated development environment for IoT
BIGTREETECH-SKR-V1.3 - 32bit board with LPC1768, support marlin2.0 and smoothieware, support lcd2004/12864, On-board TMC2130 SPI interface and TMC2208 UART interface no additional wiring is required