KlipperSettingsPlugin VS rubedo

# _____ __ _ _ _ # / ____| / _(_) | | (_) # | | ___ _ __ | |_ _ __ _ _ _ _ __ __ _| |_ _ ___ _ __ ___ # | | / _ \| '_ \| _| |/ _` | | | | '__/ _` | __| |/ _ \| '_ \/ __| # | |___| (_) | | | | | | | (_| | |_| | | | (_| | |_| | (_) | | | \__ \ # \_____\___/|_| |_|_| |_|\__, |\__,_|_| \__,_|\__|_|\___/|_| |_|___/ # __/ | # |___/ # # Klipper Configurations - Flsun Super Racer # Version 3.0 # # Guislain Cyril ######################################## # Firmware Settings ######################################## # MKS Robin Nano V3.0/V3.1 # When running "make menuconfig" # # [*] Enable extra low-level configuration options # Micro-controller Architecture (STMicroelectronics STM32) ---> # Processor model (STM32F407) ---> # Bootloader offset (48KiB bootloader (MKS Robin Nano V3)) ---> # Clock Reference (8 MHz crystal) ---> # Communication interface (USB (on PA11/PA12)) ---> # USB ids ---> # () GPIO pins to set at micro-controller startup (NEW) # # Note that the "make flash" command does not work with this board. # Rename the file out/klipper.bin to Robin_nano_v3.bin, copy it an microSD # card, insert it in the printer and restart it. ######################################## # Editable Settings ######################################## # Notes: Some settings can be enabled or disabled by removing or adding the '#' symbol # # PID (pid_Kp, pid_Ki, pid_Kd) --> [extruder] and [heater_bed] sections # E-Steps Extruder (rotation_distance) --> [extruder] section --> = * / # Pressure Advance (pressure_advance) --> [extruder] section -- See: https://www.klipper3d.org/Pressure_Advance.html # Firmware Retraction --> [firmware_retraction] section -- Requires "Klipper Settings Plugin" for Cura -- See: https://github.com/jjgraphix/KlipperSettingsPlugin # ADXL345 function for resonance testing --> Enable/Disable [include adxl345_pico.cfg] or [include adxl345_fysetc.cfg] -- Configuration in [input_shaper] section -- See: https://www.klipper3d.org/Measuring_Resonances.html # NeoPixels function --> Enable/Disable [include neopixels.cfg] # Timelapse function --> Enable/Disable [include timelapse.cfg] ######################################## # Included Files ######################################## [include macros.cfg] #[include adxl345_pico.cfg] #Enable if you want to use ADXL with Rapsberry Pi Pico #[include adxl345_fysetc.cfg] #Enable if you want to use ADXL with Fysetc Portable Input Shaper #[include timelapse.cfg] #Enable if you want to use Timelapse #[include neopixels.cfg] #Enable if you want to use Neopixels ######################################## # Printer Settings ######################################## [printer] kinematics: delta max_velocity: 300 max_accel: 4000 max_accel_to_decel: 2000 square_corner_velocity: 5 max_z_velocity: 300 max_z_accel: 1500 # delta_radius: 132 # minimum_z_position: -25 minimum_z_position: -5 print_radius: 132 #delta_radius: 151.7 ######################################## # X Stepper Motor & Driver Settings ######################################## [stepper_a] step_pin: PE3 dir_pin: PE2 enable_pin: !PE4 microsteps: 16 rotation_distance: 40 endstop_pin: PA15 ##homing_speed: 50 homing_speed: 40 homing_retract_dist: 5.0 homing_retract_speed: 10 ##angle: 210 #position_endstop: 336 #arm_length = 315 [tmc2209 stepper_a] uart_pin: PD5 run_current: 1.138 hold_current: 0.5 stealthchop_threshold: 999999 ######################################## # Y Stepper Motor & Driver Settings ######################################## [stepper_b] step_pin: PE0 dir_pin: PB9 enable_pin: !PE1 microsteps: 16 rotation_distance: 40 endstop_pin: PD2 #angle: 330 [tmc2209 stepper_b] uart_pin: PD7 run_current: 1.138 hold_current: 0.5 stealthchop_threshold: 999999 ######################################## # Z Stepper Motor & Driver Settings ######################################## [stepper_c] step_pin: PB5 dir_pin: PB4 enable_pin: !PB8 microsteps: 16 rotation_distance: 40 endstop_pin: PC4 #angle: 90 [tmc2209 stepper_c] uart_pin: PD4 run_current: 1.138 hold_current: 0.5 stealthchop_threshold: 999999 ######################################## # Extruder & Driver Settings ######################################## [extruder] step_pin: PD6 dir_pin: !PD3 enable_pin: !PB3 microsteps: 16 rotation_distance: 8.9 #7.805 nozzle_diameter: 0.4 filament_diameter: 1.750 heater_pin: PE5 sensor_type: EPCOS 100K B57560G104F sensor_pin: PC1 min_temp: -5 max_temp: 275 max_extrude_cross_section: 110 max_extrude_only_distance: 1100 pressure_advance: 0.04 #commented_out_in_stock_profile #pressure_advance_smooth_time: 0.01 #control = pid #pid_kp = 18.240 #pid_ki = 0.558 #pid_kd = 149.109 [tmc2209 extruder] uart_pin: PD9 run_current: 1.1 hold_current: 0.5 stealthchop_threshold: 999999 ######################################## # Bed Settings ######################################## [heater_bed] heater_pin: PA0 sensor_type: EPCOS 100K B57560G104F sensor_pin: PC0 min_temp: -5 max_temp: 115 #control = pid #pid_kp = 71.041 #pid_ki = 1.422 #pid_kd = 887.123 ######################################## # Filament Sensor Settings ######################################## [filament_switch_sensor filament_sensor] pause_on_runout: True runout_gcode: M600 switch_pin: PA4 ######################################## # Fans Settings ######################################## [fan] pin: PC14 [heater_fan Hotend] pin: PB0 ## heater_temp: 50.0 ######################################## # Probe Settings ######################################## [probe] pin: !PC8 x_offset: 0 y_offset: 0 #z_offset: 0 #z_offset: 16.85 speed: 10 lift_speed: 50 samples: 3 samples_result: average ##sample_retract_dist: 6 sample_retract_dist: 3 samples_tolerance: 0.02 samples_tolerance_retries: 5 ######################################## # Delta Calibration & Mesh Settings ######################################## [delta_calibrate] radius: 130 horizontal_move_z: 30 speed: 100 [bed_mesh] speed: 100 horizontal_move_z: 30 mesh_radius: 130 mesh_origin: 0,0 mesh_pps: 4,4 round_probe_count: 9 algorithm: bicubic bicubic_tension: 0.1 move_check_distance: 3 #fade_start: 1 #fade_end: 30 ######################################## # Temperature Controls ######################################## [verify_heater extruder] max_error: 500 hysteresis: 20 [verify_heater heater_bed] max_error: 120 hysteresis: 5 ######################################## # Firmware Retraction Settings ######################################## [firmware_retraction] retract_length: 6.5 retract_speed: 35 unretract_extra_length: 0.05 unretract_speed: 35 ######################################## # Input Shaper Settings ######################################## [input_shaper] shaper_freq_x: 25.00 shaper_type_x = mzv shaper_freq_y: 23.29 shaper_type_y = mzv ######################################## # G-Code Macros & Events ######################################## [idle_timeout] timeout: 1800 [save_variables] filename: ~/printer_data/config/variables.cfg [gcode_arcs] resolution: 0.1 [pause_resume] [display_status] [respond] [exclude_object] [virtual_sdcard] path: ~/printer_data/gcodes [endstop_phase stepper_a] endstop_align_zero: false [endstop_phase stepper_b] endstop_align_zero: false [endstop_phase stepper_c] endstop_align_zero: false ######################################## # MCU Settings ######################################## [mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_57002D000C50414238323520-if00 restart_method: command [temperature_sensor Speeder_Pad] sensor_type: temperature_host min_temp: 10 max_temp: 100 [temperature_sensor Motherboard] sensor_type: temperature_mcu min_temp: 0 max_temp: 100 ######################################## # LED Settings ######################################## [neopixel NeoPixels] pin: PB2 chain_count: 34 color_order: GRB initial_RED: 0.0 initial_GREEN: 0.0 initial_BLUE: 0.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [probe] #*# z_offset = 16.326 #*# #*# [endstop_phase stepper_a] #*# trigger_phase = 0/64 #*# #*# [endstop_phase stepper_b] #*# trigger_phase = 9/64 #*# #*# [endstop_phase stepper_c] #*# trigger_phase = 30/64 #*# #*# [printer] #*# delta_radius = 151.506093 #*# #*# [stepper_a] #*# angle = 209.732548 #*# arm_length = 315.000000 #*# position_endstop = 335.292877 #*# #*# [stepper_b] #*# angle = 330.028791 #*# arm_length = 315.000000 #*# position_endstop = 335.177828 #*# #*# [stepper_c] #*# angle = 90.000000 #*# arm_length = 315.000000 #*# position_endstop = 335.740631 #*# #*# [heater_bed] #*# control = pid #*# pid_kp = 71.866 #*# pid_ki = 2.692 #*# pid_kd = 479.709 #*# #*# [extruder] #*# control = pid #*# pid_kp = 25.756 #*# pid_ki = 0.923 #*# pid_kd = 179.647 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.555981, -0.555981, -0.555981, -0.555981, -0.555981, -0.555981, -0.555981, -0.555981, -0.555981 #*# -0.536382, -0.536382, -0.536382, -0.551881, -0.518557, -0.528638, -0.495733, -0.495733, -0.495733 #*# -0.523417, -0.523417, -0.541177, -0.583445, -0.555582, -0.505105, -0.490982, -0.439538, -0.439538 #*# -0.497124, -0.497124, -0.554386, -0.534127, -0.554717, -0.541424, -0.440815, -0.428654, -0.428654 #*# -0.489415, -0.548363, -0.561618, -0.541190, -0.531061, -0.507257, -0.488027, -0.501280, -0.528350 #*# -0.531851, -0.531851, -0.533378, -0.595097, -0.582416, -0.581133, -0.530884, -0.552342, -0.552342 #*# -0.577069, -0.577069, -0.575236, -0.599702, -0.593768, -0.594096, -0.638376, -0.621830, -0.621830 #*# -0.594444, -0.594444, -0.594444, -0.608776, -0.552521, -0.566593, -0.623934, -0.623934, -0.623934 #*# -0.552105, -0.552105, -0.552105, -0.552105, -0.552105, -0.552105, -0.552105, -0.552105, -0.552105 #*# x_count = 9 #*# y_count = 9 #*# mesh_x_pps = 4 #*# mesh_y_pps = 4 #*# algo = bicubic #*# tension = 0.1 #*# min_x = -130.0 #*# max_x = 130.0 #*# min_y = -130.0 #*# max_y = 130.0 #*# #*# [delta_calibrate] #*# height0 = 19.925 #*# height0_pos = 25228.333,25223.667,25261.667 #*# height1 = 19.925 #*# height1_pos = 30845.000,30850.000,22257.667 #*# height2 = 19.925 #*# height2_pos = 24636.667,34142.000,24686.333 #*# height3 = 19.925 #*# height3_pos = 22335.667,29925.667,29951.667 #*# height4 = 19.925 #*# height4_pos = 24456.333,24446.333,31270.667 #*# height5 = 19.925 #*# height5_pos = 29093.667,22487.000,29110.000 #*# height6 = 19.925 #*# height6_pos = 32588.333,24515.667,24562.333

jjgraphix/KlipperSettingsPlugin: Ultimaker Cura plugin to ... - GitHub https://github.com/jjgraphix/KlipperSettingsPlugin

SS is great but I find parts of it frustrating so I also use Cura and others depending on the project. I've been developing a Klipper plugin for Cura you may find useful that can found in my profile or on Github. Still technically in beta as I haven't had as much time to work on it but I'm nearly ready to make the next release public. Haven't tested the latest cura but it should be fine.

FYI if you're using Cura, my recent Klipper Plugin has tuning tower presets like this built in that execute all necessary velocity changes and other commands in the gcode so they don't need to be set manually or in the config.

The Klipper Settings Plugin is compatible with the new Cura 5.0 and creates everything in a new Klipper Settings category with a number of new options.