Marlin
marlin-aquila
Marlin | marlin-aquila | |
---|---|---|
877 | 2 | |
2,142 | 4 | |
- | - | |
0.0 | 1.5 | |
6 months ago | 12 months ago | |
C++ | C++ | |
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
marlin-aquila
-
Marlin 2, Linear Advance, Board 1.0.1, TMC2208
I'm sooooo confused! So looking at putting Marlin v2.1.1 onto my Aquila, currently running Alexqzm's v1.3.5. One of many good(?) new things in v2 is the 'linear advance' which I've read promising things about. But will it work??!? I have a 1.0.1 G32 board from 2021 which supposedly has the TMC2208 stepper drivers (or perhaps the MS35775 clone of the TMC2208) which apparently can't do linear advance due to a bug in its on-chip firmware. Or so says some sources, whereas many other people claim to have it working. And while I would like to give those people the benefit of the doubt, not everything on the 'net is correct, and those people may not (or may) truly know if it is working. Again, I wanna give these people the benefit of the doubt but many so called "experts" aren't. Then there is this post from Alexqzm himself on how to get it working in his 1.3.5 firmware, but his way involves soldering a jumper onto the board. (This is the "UART" mod??) I'm pro'ly gonna try the upgrade to v2 with or without the linear advance so the real question is "do I enable it in the firmware/source code" (before re-compiling & flashing) and do I need to add the jumper? I'm getting contradicting info.
- Marlin 2.1.1 for G32 with Linear Advance without uart mod
What are some alternatives?
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
MRiscoCProUI - This is optimized firmware for Voxelab Aquila & Ender3 V2/S1 3D printers.
klipper - Klipper is a 3d-printer firmware
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
VoronUsers - Voron Community mods
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
FluiddPI - FluiddPi - A Pi image with Klipper, Moonraker, Fluidd and Web Camera support pre-installed.
PrusaSlicer - G-code generator for 3D printers (RepRap, Makerbot, Ultimaker etc.)
Ender3V2S1 - This is optimized firmware for Ender3 V2/S1 3D printers.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.