Marlin
MRiscoCProUI
Our great sponsors
Marlin | MRiscoCProUI | |
---|---|---|
877 | 98 | |
2,142 | 67 | |
- | - | |
0.0 | 0.0 | |
6 months ago | 5 days ago | |
C++ | C++ | |
GNU General Public License v3.0 only | GNU General Public License v3.0 or later |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
MRiscoCProUI
-
Marlin VS MRiscoCProUI - a user suggested alternative
2 projects | 25 Jan 2024
This is where it has moved to
-
BFPTouch on AlexFirmware
I don't know much about compiling firmware but it might be better to base the edits on Mriscoc instead of Alex's as it has much better support for the H32 chip so should be a lot easier to compile.
- Release Aquila Build for September · MRiscoCProUI
-
N32 Firmware question
I'm see that there are newer firmware available. This one (https://github.com/classicrocker883/MRiscoCProUI/releases), for example.
- major update HC32 Build for September · classicrocker883/MRiscoCProUI
- Release Aquila Build for August · classicrocker883/MRiscoCProUI
- Ender-3 Build for July · classicrocker883/MriscocProUI
- Release July Update Build pt. 2 · classicrocker883/MriscocProUI
-
BLtouch doesn't trigger Z-stop on aquila x2 H32
I just thought of another thing you could try. Give Mriscoc ProUI FW as it may have the option to configure this or is already properly set up for this version of the probe.
-
Help! got message 'Recv: Error:G2/G3 bad parameters'
If for some reason your FW does not support those Gcodes then update it to the latest version, or try Alex's or Mriscoc ProUI firmwares.
What are some alternatives?
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
klipper - Klipper is a 3d-printer firmware
Marlin-H32 - JyersUI port for Aquila H32 Printers
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
Special_Configurations - In this repository there are the configuration files and releases for the Professional firmware with several features enabled. You can use the Configurator if you want to compile your own custom set of features. You can also request a pre-made binary for a small contribution on the Patreon site.
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
Marlin-Alex - Firmware mainly for Voxelab Aquila or Creality Ender w/ 4.2.7 board or G32/N32 chips
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
marlin-aquila - Marlin fork for Voxelab Aquila
VoronUsers - Voron Community mods
Marlin-H32 - Marlin for HC32F460 based printers (now in upstream)