Klipper-macros Alternatives

klipper-macros reviews and mentions

• Incompatible Gcodes: What to Do About Them?
  1 project | /r/klippers | 18 Sep 2022

  Alternatively, you could try using this macro to try to get Klipper to make use of those M205 commands, but I wouldn't recommend it. Klipper handles acceleration just fine on its own without the slicer controlling it.

• Ender 5 plus with SKR mini E3 V2 running klipper Z axis config help
  1 project | /r/ender5plus | 7 Sep 2022

  [include fluidd.cfg] # This file contains common pin mappings for the BIGTREETECH SKR mini # E3 v2.0. To use this config, the firmware should be compiled for the # STM32F103 with a "28KiB bootloader" and USB communication. Also, # select "Enable extra low-level configuration options" and configure # "GPIO pins to set at micro-controller startup" to "!PA14". # The "make flash" command does not work on the SKR mini E3. Instead, # after running "make", copy the generated "out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the SKR # mini E3 with that SD card. # See docs/Config_Reference.md for a description of parameters. [stepper_x] step_pin: PB13 dir_pin: !PB12 enable_pin: !PB14 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC0 position_endstop: 360 position_max: 360 homing_speed: 50 [tmc2209 stepper_x] uart_pin: PC11 tx_pin: PC10 uart_address: 0 run_current: 0.680 stealthchop_threshold: 999999 [stepper_y] step_pin: PB10 dir_pin: !PB2 enable_pin: !PB11 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC1 position_endstop: 360 position_max: 360 homing_speed: 50 [tmc2209 stepper_y] uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.700 stealthchop_threshold: 999999 [stepper_z] step_pin: PB0 dir_pin: !PC5 enable_pin: !PB1 microsteps: 16 rotation_distance: 8 endstop_pin: probe:z_virtual_endstop position_min: -2.7 position_max: 400 [tmc2209 stepper_z] uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.800 stealthchop_threshold: 999999 [extruder] step_pin: PB3 dir_pin: !PB4 enable_pin: !PD2 microsteps: 16 rotation_distance: 33.500 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PC8 sensor_type: EPCOS 100K B57560G104F sensor_pin: PA0 control: pid pid_Kp: 21.527 pid_Ki: 1.063 pid_Kd: 108.982 min_temp: 0 max_temp: 250 [tmc2209 extruder] uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 stealthchop_threshold: 999999 [heater_bed] heater_pin: PC9 sensor_type: ATC Semitec 104GT-2 sensor_pin: PC3 control: pid pid_Kp: 54.027 pid_Ki: 0.770 pid_Kd: 948.182 min_temp: 0 max_temp: 130 [bltouch] sensor_pin: ^PC2 control_pin: PA1 pin_move_time: 0.675 stow_on_each_sample: False probe_with_touch_mode: True pin_up_touch_mode_reports_triggered: False x_offset: -27.5 y_offset: -2.5 #z_offset: 2.320 speed: 20 lift_speed: 20 samples: 1 sample_retract_dist:5 samples_tolerance_retries: 3 [safe_z_home] home_xy_position: 207.5, 182.5 speed: 200 z_hop: 5 z_hop_speed: 20 [bed_mesh] speed: 200 horizontal_move_z: 5 mesh_min: 40,40 mesh_max: 320,320 probe_count: 5 mesh_pps: 2,2 algorithm: bicubic fade_start: 1 fade_end: 10 fade_target: 0 [heater_fan heatbreak_cooling_fan] pin: PC7 [fan] pin: PC6 [mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_35FFD8053043553528500951-if00 [printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100 [static_digital_output usb_pullup_enable] pins: !PA14 [board_pins] aliases: # EXP1 header     EXP1_1=PB5,  EXP1_3=PA9,   EXP1_5=PA10, EXP1_7=PB8,  EXP1_9=,     EXP1_2=PA15, EXP1_4=, EXP1_6=PB9,  EXP1_8=PB15, EXP1_10=<5V> # See the sample-lcd.cfg file for definitions of common LCD displays. [t5uid1] firmware: dgus_reloaded machine_name: Ender 5 Plus volume: 60 brightness: 50 z_min: 0 z_max: 410 # https://github.com/Desuuuu/klipper-macros # If you want to use these macros, follow the instructions from the repository # and uncomment the following lines. #[save_variables] #filename: ~/variables.cfg # #[delayed_gcode macros_initialize] #initial_duration: 1 #gcode: #  INITIALIZE_VARIABLE VARIABLE=park_x VALUE=20 #  INITIALIZE_VARIABLE VARIABLE=park_y VALUE=340 #  INITIALIZE_VARIABLE VARIABLE=bowden_len VALUE=570 # #[include macros/\.cfg]* #\# <---------------------- SAVE_CONFIG ---------------------->* #\# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.* #\#* #\# [bltouch]* #\# z_offset = 5.010*

• How to install Desuuuu's Klipper Fork with Fluidd on a CR10S Pro V2 (And other printers too)
  2 projects | /r/klippers | 13 Jul 2022

  # This file contains pin mappings for the Creality CR-10S Pro V2. To use # this config, the firmware should be compiled for the AVR atmega2560. [stepper_x] step_pin: PF0 dir_pin: PF1 enable_pin: !PD7 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PE5 position_endstop: 0 position_min: 0 position_max: 300 homing_speed: 50 homing_retract_dist: 5 [stepper_y] step_pin: PF6 dir_pin: !PF7 enable_pin: !PF2 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PJ1 position_endstop: 0 position_min: 0 position_max: 310 homing_speed: 50 homing_retract_dist: 5 [stepper_z] step_pin: PL3 dir_pin: !PL1 enable_pin: !PK0 rotation_distance: 8 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: probe:z_virtual_endstop position_min: -1 position_max: 351 [extruder] step_pin: PA4 dir_pin: PA6 enable_pin: !PA2 rotation_distance: 22.900 microsteps: 16 full_steps_per_rotation: 200 nozzle_diameter: 0.400 filament_diameter: 1.750 max_extrude_only_distance: 500.0 max_extrude_only_velocity: 70.0 max_extrude_only_accel: 1000.0 heater_pin: PB4 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK5 control: pid pid_Kp: 22.2 pid_Ki: 1.08 pid_Kd: 114 min_extrude_temp: 170 min_temp: 5 max_temp: 275 [heater_bed] heater_pin: PH5 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK6 control: pid pid_Kp: 690.34 pid_Ki: 111.47 pid_Kd: 1068.83 min_temp: 5 max_temp: 140 [fan] pin: PH6 [mcu] serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AB0KFEO7-if00-port0 #REPLACE WITH YOUR PRINTER'S SERIAL**** [printer] kinematics: cartesian max_velocity: 200 max_accel: 1500 max_z_velocity: 10 max_z_accel: 100 [bltouch] sensor_pin: ^PD2 control_pin: PB5 stow_on_each_sample: False probe_with_touch_mode: True x_offset: -27 y_offset: -2 z_offset: 0 speed: 4.0 samples: 2 sample_retract_dist: 3.0 [safe_z_home] home_xy_position: 177,155 speed: 80.0 z_hop: 10.0 z_hop_speed: 5.0 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 5, 5 mesh_max: 268, 305 probe_count: 5,5 fade_start: 1 fade_end: 10 [filament_switch_sensor e0_sensor] switch_pin: PE4 pause_on_runout: False runout_gcode: PAUSE_PARK [pause_resume] [respond] default_type: echo [t5uid1] firmware: dgus_reloaded machine_name: The Replimat volume: 60 brightness: 50 z_min: 0 z_max: 350 [virtual_sdcard] path: ~/gcode_files [display_status] [pause_resume] [gcode_macro PAUSE] description: Pause the actual running print rename_existing: PAUSE_BASE # change this if you need more or less extrusion variable_extrude: 1.0 gcode: ##### read E from pause macro ##### {% set E = printer["gcode_macro PAUSE"].extrude|float %} ##### set park positon for x and y ##### # default is your max posion from your printer.cfg {% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %} {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %} ##### calculate save lift position ##### {% set max_z = printer.toolhead.axis_maximum.z|float %} {% set act_z = printer.toolhead.position.z|float %} {% if act_z < (max_z - 2.0) %} {% set z_safe = 2.0 %} {% else %} {% set z_safe = max_z - act_z %} {% endif %} ##### end of definitions ##### PAUSE_BASE G91 {% if printer.extruder.can_extrude|lower == 'true' %} G1 E-{E} F2100 {% else %} {action_respond_info("Extruder not hot enough")} {% endif %} {% if "xyz" in printer.toolhead.homed_axes %} G1 Z{z_safe} F900 G90 G1 X{x_park} Y{y_park} F6000 {% else %} {action_respond_info("Printer not homed")} {% endif %} [gcode_macro RESUME] description: Resume the actual running print rename_existing: RESUME_BASE gcode: ##### read E from pause macro ##### {% set E = printer["gcode_macro PAUSE"].extrude|float %} #### get VELOCITY parameter if specified #### {% if 'VELOCITY' in params|upper %} {% set get_params = ('VELOCITY=' + params.VELOCITY) %} {%else %} {% set get_params = "" %} {% endif %} ##### end of definitions ##### {% if printer.extruder.can_extrude|lower == 'true' %} G91 G1 E{E} F2100 {% else %} {action_respond_info("Extruder not hot enough")} {% endif %} RESUME_BASE {get_params} [gcode_macro CANCEL_PRINT] description: Cancel the actual running print rename_existing: CANCEL_PRINT_BASE gcode: TURN_OFF_HEATERS CANCEL_PRINT_BASE # https://github.com/Desuuuu/klipper-macros # If you want to use these macros, follow the instructions from the repository # and uncomment the following lines. #[save_variables] #filename: ~/variables.cfg # #[delayed_gcode macros_initialize] #initial_duration: 1 #gcode: # INITIALIZE_VARIABLE VARIABLE=park_x VALUE=20 # INITIALIZE_VARIABLE VARIABLE=park_y VALUE=290 # INITIALIZE_VARIABLE VARIABLE=bowden_len VALUE=400 # #[include macros/*.cfg]

• how would I pause after g28?
  1 project | /r/klippers | 16 Mar 2022

  Add a macro for M600 like this one https://github.com/Desuuuu/klipper-macros/blob/master/macros/M600.cfg

• Ok, Fluidd is pretty fuckin sweet
  6 projects | /r/klippers | 11 Feb 2022

  I took a few maros from this collection that I use daily like Wipe Line and Lazy Home.

• Cr10s pro klipper config (be sure to change pid, pressure advance, screws_tilt_adjust, input_shaper, bed mesh etc. )
  1 project | /r/CR10sPRO | 19 Jan 2022

  # This is my working Config for the cr10s pro, with Bl touch, and hero me shroud. to use with the DGus LCD Firmware (Volanaro) # This file contains pin mappings for the Creality CR-10S Pro. To use # this config, the firmware should be compiled for the AVR atmega2560. [stepper_x] step_pin: PF0 dir_pin: PF1 enable_pin: !PD7 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PE5 position_endstop: 0 position_min: 0 position_max: 310 homing_speed: 50 homing_retract_dist: 5 [stepper_y] step_pin: PF6 dir_pin: !PF7 enable_pin: !PF2 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PJ1 position_endstop: -9 position_min: -9 position_max: 310 homing_speed: 50 homing_retract_dist: 5 [stepper_z] step_pin: PL3 dir_pin: !PL1 enable_pin: !PK0 rotation_distance: 8 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: probe:z_virtual_endstop position_min: -10 position_max: 317 [extruder] step_pin: PA4 dir_pin: PA6 enable_pin: !PA2 rotation_distance: 7.7669902912 microsteps: 16 full_steps_per_rotation: 200 nozzle_diameter: 0.400 filament_diameter: 1.750 max_extrude_only_distance: 500.0 max_extrude_only_velocity: 70.0 max_extrude_only_accel: 1000.0 heater_pin: PB4 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK5 control: pid pid_Kp: 22.2 pid_Ki: 1.08 pid_Kd: 114 min_extrude_temp: 170 min_temp: 5 max_temp: 275 pressure_advance = 0.067 [heater_bed] heater_pin: PH5 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK6 control: pid pid_Kp: 690.34 pid_Ki: 111.47 pid_Kd: 1068.83 min_temp: 5 max_temp: 140 [fan] pin: PH6 [mcu] baud: 250000 serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL05INK2-if00-port0 [printer] kinematics: cartesian max_velocity: 200 max_accel: 7000 max_z_velocity: 10 max_z_accel: 100 [bltouch] sensor_pin: ^PD3 control_pin: PB5 stow_on_each_sample: False probe_with_touch_mode: True x_offset: -52 y_offset: -13 #z_offset: 0 speed: 4.0 samples: 2 sample_retract_dist: 3.0 [safe_z_home] home_xy_position: 202,160 speed: 80.0 z_hop: 10.0 z_hop_speed: 5.0 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 5, 5 mesh_max: 250, 290 probe_count: 5,5 fade_start: 1 fade_end: 10 [screws_tilt_adjust] screw1: 81,47 screw1_name: front left screw screw2: 295,47 screw2_name: front right screw screw3: 295,287 screw3_name: rear right screw screw4: 81,287 screw4_name: rear left screw horizontal_move_z: 10 speed: 50 screw_thread: CW-M4 [] shaper_freq_x: 85.1 shaper_freq_y: 70.1 shaper_type: mzv [filament_switch_sensor e0_sensor] switch_pin: PE4 pause_on_runout: False runout_gcode: PAUSE_PARK [pause_resume] [respond] default_type: echo [t5uid1] firmware: dgus_reloaded machine_name: CR-10S Pro #volume: 60 brightness: 50 z_min: 0 z_max: 350 # https://github.com/Desuuuu/klipper-macros # If you want to use these macros, follow the instructions from the repository # and uncomment the following lines. #[save_variables] #filename: ~/variables.cfg # #[delayed_gcode macros_initialize] #initial_duration: 1 #gcode: # INITIALIZE_VARIABLE VARIABLE=park_x VALUE=20 # INITIALIZE_VARIABLE VARIABLE=park_y VALUE=290 # INITIALIZE_VARIABLE VARIABLE=bowden_len VALUE=400 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [bltouch] #*# z_offset = 1.690 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.156250, -0.173750, -0.191250, -0.212500, -0.290000 #*# -0.052500, -0.027500, -0.036250, -0.047500, -0.112500 #*# -0.035000, -0.002500, -0.006250, -0.030000, -0.066250 #*# -0.140000, -0.096250, -0.082500, -0.100000, -0.147500 #*# -0.315000, -0.257500, -0.246250, -0.251250, -0.305000 #*# tension = 0.2 #*# min_x = 5.0 #*# algo = lagrange #*# y_count = 5 #*# mesh_y_pps = 2 #*# min_y = 5.0 #*# x_count = 5 #*# max_y = 290.0 #*# mesh_x_pps = 2 #*# max_x = 250.0 #*# #*# [t5uid1] #*# volume = 10

• A note from our sponsor - InfluxDB
  www.influxdata.com | 1 May 2024

  Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality. Learn more →