-
InfluxDB
Power Real-Time Data Analytics at Scale. Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality.
# This is my working Config for the cr10s pro, with Bl touch, and hero me shroud. to use with the DGus LCD Firmware (Volanaro) # This file contains pin mappings for the Creality CR-10S Pro. To use # this config, the firmware should be compiled for the AVR atmega2560. [stepper_x] step_pin: PF0 dir_pin: PF1 enable_pin: !PD7 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PE5 position_endstop: 0 position_min: 0 position_max: 310 homing_speed: 50 homing_retract_dist: 5 [stepper_y] step_pin: PF6 dir_pin: !PF7 enable_pin: !PF2 rotation_distance: 40 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: ^PJ1 position_endstop: -9 position_min: -9 position_max: 310 homing_speed: 50 homing_retract_dist: 5 [stepper_z] step_pin: PL3 dir_pin: !PL1 enable_pin: !PK0 rotation_distance: 8 microsteps: 16 full_steps_per_rotation: 200 endstop_pin: probe:z_virtual_endstop position_min: -10 position_max: 317 [extruder] step_pin: PA4 dir_pin: PA6 enable_pin: !PA2 rotation_distance: 7.7669902912 microsteps: 16 full_steps_per_rotation: 200 nozzle_diameter: 0.400 filament_diameter: 1.750 max_extrude_only_distance: 500.0 max_extrude_only_velocity: 70.0 max_extrude_only_accel: 1000.0 heater_pin: PB4 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK5 control: pid pid_Kp: 22.2 pid_Ki: 1.08 pid_Kd: 114 min_extrude_temp: 170 min_temp: 5 max_temp: 275 pressure_advance = 0.067 [heater_bed] heater_pin: PH5 sensor_type: EPCOS 100K B57560G104F sensor_pin: PK6 control: pid pid_Kp: 690.34 pid_Ki: 111.47 pid_Kd: 1068.83 min_temp: 5 max_temp: 140 [fan] pin: PH6 [mcu] baud: 250000 serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL05INK2-if00-port0 [printer] kinematics: cartesian max_velocity: 200 max_accel: 7000 max_z_velocity: 10 max_z_accel: 100 [bltouch] sensor_pin: ^PD3 control_pin: PB5 stow_on_each_sample: False probe_with_touch_mode: True x_offset: -52 y_offset: -13 #z_offset: 0 speed: 4.0 samples: 2 sample_retract_dist: 3.0 [safe_z_home] home_xy_position: 202,160 speed: 80.0 z_hop: 10.0 z_hop_speed: 5.0 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 5, 5 mesh_max: 250, 290 probe_count: 5,5 fade_start: 1 fade_end: 10 [screws_tilt_adjust] screw1: 81,47 screw1_name: front left screw screw2: 295,47 screw2_name: front right screw screw3: 295,287 screw3_name: rear right screw screw4: 81,287 screw4_name: rear left screw horizontal_move_z: 10 speed: 50 screw_thread: CW-M4 [] shaper_freq_x: 85.1 shaper_freq_y: 70.1 shaper_type: mzv [filament_switch_sensor e0_sensor] switch_pin: PE4 pause_on_runout: False runout_gcode: PAUSE_PARK [pause_resume] [respond] default_type: echo [t5uid1] firmware: dgus_reloaded machine_name: CR-10S Pro #volume: 60 brightness: 50 z_min: 0 z_max: 350 # https://github.com/Desuuuu/klipper-macros # If you want to use these macros, follow the instructions from the repository # and uncomment the following lines. #[save_variables] #filename: ~/variables.cfg # #[delayed_gcode macros_initialize] #initial_duration: 1 #gcode: # INITIALIZE_VARIABLE VARIABLE=park_x VALUE=20 # INITIALIZE_VARIABLE VARIABLE=park_y VALUE=290 # INITIALIZE_VARIABLE VARIABLE=bowden_len VALUE=400 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [bltouch] #*# z_offset = 1.690 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.156250, -0.173750, -0.191250, -0.212500, -0.290000 #*# -0.052500, -0.027500, -0.036250, -0.047500, -0.112500 #*# -0.035000, -0.002500, -0.006250, -0.030000, -0.066250 #*# -0.140000, -0.096250, -0.082500, -0.100000, -0.147500 #*# -0.315000, -0.257500, -0.246250, -0.251250, -0.305000 #*# tension = 0.2 #*# min_x = 5.0 #*# algo = lagrange #*# y_count = 5 #*# mesh_y_pps = 2 #*# min_y = 5.0 #*# x_count = 5 #*# max_y = 290.0 #*# mesh_x_pps = 2 #*# max_x = 250.0 #*# #*# [t5uid1] #*# volume = 10