-
InfluxDB
Power Real-Time Data Analytics at Scale. Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality.
[include fluidd.cfg] # This file contains common pin mappings for the BIGTREETECH SKR mini # E3 v2.0. To use this config, the firmware should be compiled for the # STM32F103 with a "28KiB bootloader" and USB communication. Also, # select "Enable extra low-level configuration options" and configure # "GPIO pins to set at micro-controller startup" to "!PA14". # The "make flash" command does not work on the SKR mini E3. Instead, # after running "make", copy the generated "out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the SKR # mini E3 with that SD card. # See docs/Config_Reference.md for a description of parameters. [stepper_x] step_pin: PB13 dir_pin: !PB12 enable_pin: !PB14 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC0 position_endstop: 360 position_max: 360 homing_speed: 50 [tmc2209 stepper_x] uart_pin: PC11 tx_pin: PC10 uart_address: 0 run_current: 0.680 stealthchop_threshold: 999999 [stepper_y] step_pin: PB10 dir_pin: !PB2 enable_pin: !PB11 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC1 position_endstop: 360 position_max: 360 homing_speed: 50 [tmc2209 stepper_y] uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.700 stealthchop_threshold: 999999 [stepper_z] step_pin: PB0 dir_pin: !PC5 enable_pin: !PB1 microsteps: 16 rotation_distance: 8 endstop_pin: probe:z_virtual_endstop position_min: -2.7 position_max: 400 [tmc2209 stepper_z] uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.800 stealthchop_threshold: 999999 [extruder] step_pin: PB3 dir_pin: !PB4 enable_pin: !PD2 microsteps: 16 rotation_distance: 33.500 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PC8 sensor_type: EPCOS 100K B57560G104F sensor_pin: PA0 control: pid pid_Kp: 21.527 pid_Ki: 1.063 pid_Kd: 108.982 min_temp: 0 max_temp: 250 [tmc2209 extruder] uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 stealthchop_threshold: 999999 [heater_bed] heater_pin: PC9 sensor_type: ATC Semitec 104GT-2 sensor_pin: PC3 control: pid pid_Kp: 54.027 pid_Ki: 0.770 pid_Kd: 948.182 min_temp: 0 max_temp: 130 [bltouch] sensor_pin: ^PC2 control_pin: PA1 pin_move_time: 0.675 stow_on_each_sample: False probe_with_touch_mode: True pin_up_touch_mode_reports_triggered: False x_offset: -27.5 y_offset: -2.5 #z_offset: 2.320 speed: 20 lift_speed: 20 samples: 1 sample_retract_dist:5 samples_tolerance_retries: 3 [safe_z_home] home_xy_position: 207.5, 182.5 speed: 200 z_hop: 5 z_hop_speed: 20 [bed_mesh] speed: 200 horizontal_move_z: 5 mesh_min: 40,40 mesh_max: 320,320 probe_count: 5 mesh_pps: 2,2 algorithm: bicubic fade_start: 1 fade_end: 10 fade_target: 0 [heater_fan heatbreak_cooling_fan] pin: PC7 [fan] pin: PC6 [mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_35FFD8053043553528500951-if00 [printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100 [static_digital_output usb_pullup_enable] pins: !PA14 [board_pins] aliases: # EXP1 header EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=, EXP1_2=PA15, EXP1_4=, EXP1_6=PB9, EXP1_8=PB15, EXP1_10=<5V> # See the sample-lcd.cfg file for definitions of common LCD displays. [t5uid1] firmware: dgus_reloaded machine_name: Ender 5 Plus volume: 60 brightness: 50 z_min: 0 z_max: 410 # https://github.com/Desuuuu/klipper-macros # If you want to use these macros, follow the instructions from the repository # and uncomment the following lines. #[save_variables] #filename: ~/variables.cfg # #[delayed_gcode macros_initialize] #initial_duration: 1 #gcode: # INITIALIZE_VARIABLE VARIABLE=park_x VALUE=20 # INITIALIZE_VARIABLE VARIABLE=park_y VALUE=340 # INITIALIZE_VARIABLE VARIABLE=bowden_len VALUE=570 # #[include macros/\.cfg]* #\# <---------------------- SAVE_CONFIG ---------------------->* #\# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.* #\#* #\# [bltouch]* #\# z_offset = 5.010*