Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality. Learn more →
AVR-Guidance Alternatives
Similar projects and alternatives to AVR-Guidance
-
megaTinyCore
Arduino core for the tinyAVR 0/1/2-series - Ones's digit 2,4,5,7 (pincount, 8,14,20,24), tens digit 0, 1, or 2 (featureset), preceded by flash in kb. Library maintainers: porting help available!
-
jtag2updi
UPDI programmer software for Arduino (targets Tiny AVR-0/1/2, Mega AVR-0 and AVR-DA/DB MCUs)
-
InfluxDB
Power Real-Time Data Analytics at Scale. Get real-time insights from all types of time series data with InfluxDB. Ingest, query, and analyze billions of data points in real-time with unbounded cardinality.
-
MegaCoreX
An Arduino hardware package for ATmega4809, ATmega4808, ATmega3209, ATmega3208, ATmega1609, ATmega1608, ATmega809 and ATmega808
NOTE:
The number of mentions on this list indicates mentions on common posts plus user suggested alternatives.
Hence, a higher number means a better AVR-Guidance alternative or higher similarity.
AVR-Guidance reviews and mentions
Posts with mentions or reviews of AVR-Guidance.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-04-06.
- How to upload code onto a blank ATTiny1616 chip?
-
Best way to migrate from an arduino-based system to a purely microcontroller-IC one?
Check out the newer attiny chips......cheap, available, and LOW POWER. No external crystal or other components required. Programmable via Arduino IDE.,,see: https://github.com/SpenceKonde/megaTinyCore You can use any arduino as a programmer (JTAGTOUPDI) or make one with a cheap serial adapter: https://github.com/SpenceKonde/AVR-Guidance/blob/master/UPDI/jtag2updi.md
-
I got an ATTiny1616 development board. How do I connect the two and flash the code (basic blink example) from the Arduino Nano to the ATTiny1616? Thanks.
For Serial UPDI attach either a diode or resistor between RX and TX, then connect RX to UPDI PIN, along with and VCC and GND. https://github.com/SpenceKonde/AVR-Guidance/blob/master/UPDI/jtag2updi.md
-
Problem uploading firmware via UPDI when SerialUPDI circuit is installed
I own a PICKIT4, so normally I would just breakout Vcc, Gnd, and UPDI pins and directly connect my PICKIT to it. This time though my friend recommended me to also include a SerialUPDI circuit on board to accommodate Arduino users (and ones without PICKIT in general). The part related to SerialUPDI are JP3, JP4, D35, and R5.
-
TS10 aux light question
Yup, that should do the trick. You might want to give this guide a good read-through. It has some chip-specific tips (search for FTDI) and general recommendations for wiring and removing the Rx LED if it gives you troubles.
-
How to flash firmware on the SP10 Pro (Photos at the bottom)
Choice of hardware
-
Programming the AVR128DB
You can use RX/TX with the UPDI interface directly, see https://github.com/SpenceKonde/AVR-Guidance/blob/master/UPDI/jtag2updi.md. You should at least add a resistor on the line. Then you'll be able to program it with pymcuprog in serial mode, without a bootloader.
-
[Schematic review] Tiny handheld game console
ISP looks a lot like spi. Updi is asynchronous uart. It's a lot different and I would recommend looking at serial updi.
-
A note from our sponsor - InfluxDB
www.influxdata.com | 10 May 2024
Stats
Basic AVR-Guidance repo stats
9
136
4.1
20 days ago
The primary programming language of AVR-Guidance is C++.
Popular Comparisons
Sponsored
SaaSHub - Software Alternatives and Reviews
SaaSHub helps you find the best software and product alternatives
www.saashub.com