Sovol-SV06-firmware
By spinixguy
sv06
Custom Sovol SV06 build with options for UBL, Bi-Linear, Manual Mesh, Input Shaping, and X-Twist (by hillsoftware)
Sovol-SV06-firmware | sv06 | |
---|---|---|
5 | 18 | |
81 | 118 | |
- | - | |
0.0 | 2.6 | |
4 months ago | about 1 year ago | |
C++ | ||
- | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Sovol-SV06-firmware
Posts with mentions or reviews of Sovol-SV06-firmware.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-04-04.
- Octoprint times out connecting to MCU after flashing Klipper firmware on SV06. Octoprint and Klipper can recognize Marlin firmware, but everything times out after flashing Klipper firmware.
-
Sovol SV06 Running Klipper With sonic pad
Hello there just wanted to show some kipper testing I’m doing with the SV06 it was pretty easy to set up with the sonic pad just set it up as a ender 3 s1 then skip the whole setup until the automatic bed leveling where it won’t let you skip, but if you hard reboot your printer while it’s plugged it it will bring you to the main klipper screen where you can then find your sonic pads ip address then complete replace the ender 3 s1 config with this sv06 config off github ( https://github.com/spinixguy/Sovol-SV06-firmware ) This was just a test print I did at 10000mm acceleration and 250mm travel and printing speed in cura slicer
- I'm not sure what to call this but it's really ugly, happened since I went to Klipper (see comments config)
-
SV06 Klipper?
I'm working on a very comprehensive, one stop shop kind of klipper config, but it's untested. For now, I can recommend this instead https://github.com/spinixguy/Sovol-SV06-firmware
-
Klipper on SV06
Took the firmware and config from this repo: https://github.com/spinixguy/Sovol-SV06-firmware
sv06
Posts with mentions or reviews of sv06.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-05-03.
-
First layer issues. Leveled bed, trammed x axis. SV06
There is also a software solution. If you are running the stock firmware, flash a version of Marlin with Unified Bed Leveling (UBL) enabled. It will let you use the bed sensor to build a mesh, then go through each point and manually adjust it as needed. You can either compile it yourself or just use the UBL version from here: https://github.com/hillsoftware/sv06
-
Firmware
Hi I recently updated to this firmware https://github.com/hillsoftware/sv06 (V57). After completing the purge strip the printer accelerates a bit faster than I'd like, and It sounds like the Y axis is stepper motor is struggling. I've tried to make changes to the firmware but get this error, even without any of my changes I still get the same error. Has anyone experienced this? Thanks, Alex
-
SV06 Plus - Marlin 2.1.2
Was Marlin previously working and suddenly stopped? I would say, start with a different micro SD, format to FAT32 and flash the original Sovol3D firmware back to the printer. Guide and downloads found here. Then on another freshly formatted micro SD follow this guide to download and install Marlin from GitHub
- If you’re not on klipper you’re leaving performance on the table!
-
Bed mesh calibrate
Unfortunately the auto bed leveling on the SV06 can be quite bad. I had the same issue. The way I solved it was by installing the manual mesh version of this custom firmware.
-
SV06 won’t automatically pause at set layer height
While I’m not sure exactly what’s causing your specific issue I can tell you the revision of Marlin that Sovol uses is quite old. I’d recommend flashing Hillsoftware’s v57 pre-complied release. It fixes a lot of issues and adds a lot of features that Sovol chose to leave out. Just follow the directions during your setup and you should be good to go with any mid print pausing or filament changes.
-
I can't make SV06 print properly! Almost giving up!
Tried to change the frimware GitHub - hillsoftware/sv06: Custom Sovol SV06 build with UBL and X-Twist , used bi-linear version got the same problem as sovol firmare with 25 points bed leveling.
- Weird things with the SV06 ABL
-
How to fix X-Twist?
Yesterday I finally flashed the custom firmware from hillsoftware. At first I tried my luck without X-Twist-Compensation to see if the firmware with UBL could fix the problem. It didn't.
- SV06 Help
What are some alternatives?
When comparing Sovol-SV06-firmware and sv06 you can also consider the following projects:
SOVOL-SV06-Klipper-profile - Complete Klipper profile with all config files and macros to tune the printer (stock)
Sovol-SV06-firmware - 🔥 A comprehensive Klipper configuration for a variety of 3D printers 🔥