openmiko VS agent

Have a Wyze Cam V2 running openmiko. I can pull the feed via the camera's IP, but Klipper (Fluidd, Mainsail on BTT CB1) shows like below. Additionally, moonraker-timelapse throws an error. This was working fine until I tried Hyperlapse. Now I can't wrap my head around this

I'm running MainsailOS, and a Wyze cam v2 running openmiko. I have Tailscale installed on the Pi for remote access. In Mainsail config, I have the camera configured via private IP. When I access the web control panel externally, I do not get video output. Is there a way to get this to work? I do not think there's a way to connect the Wyze cam to my tailnet.If it's not possible, have any good recommendations for a good, cheap, wide-angle (110 degrees FOV or better) camera I can purchase? I wouldn't want to spend more than $25 for one. Quick search yielded this one, but don't know if there's a Klipper-community recommended one that everyone uses.

you wish lol. the mod allows you to get highest possible resolution video out of it without all the compression pixelation. its super easy to install. but it does take a little bit of linux knowledge to edit config files and stuff. heres the link if interested: https://github.com/openmiko/openmiko

I bought a used Wyze Cam V2 relatively cheap and installed OpenMiko on it for example.

I have a WyzeCamV2 running OpenMiko firmware, which supports (and I have configured for) H264 RTSP streaming. I can view the video stream through VLC with the url rtsp://192.168.1.199:8554/video3_unicast. I am executing the command docker run -p 8081:80 --name mycamera -e AGENT_CAPTURE_IPCAMERA_RTSP="rtsp://192.168.1.199:8554/video3_unicast" kerberos/agent:latest on my host. The agent seems to run fine and I can connect via browser. With our without AGENT_CAPTURE_IPCAMERA_RTSP... set, I cannot add the RTSP stream; no cameras show attached and when I try to connect one via dashboard->settings, it just spins. The logs aren't really helpful (see below).

OpenMiko is one example.

That's why I only use cameras flashed with open firmware: https://github.com/openmiko/openmiko

If all else fails, you can flash different firmware and use them locally. I'm using [OpenMiko](https://github.com/openmiko/openmiko) on my Wyze Cam v1 (I'd assume there's a similar open-source project for the v3), and Wyze themselves publishes an RTSP firmware. Without a bit of technical know-how and some supporting hardware (namely a router than supports OpenVPN) you won't have access to the stream off your local network, but you can stream locally with VLC Player.

On kerberos.io I cannot add a credit card to pay the subscription. I've tryed with different cards, but the result is always the same, like you see in the video, with no errors displayed.

I am currently in the process of evaluating kerberos.io as a NVR solution I might switch to. I have deployed the Kerberos Vault, configured a storage provider (minio) and created an account.

Kerberos.io - open source, made for enterprise scale

I'll look into zoneminder and shinobi, was looking at kerberos.io. Usually SmartPSS timing out or some cameras randomly blacks out.

I'm currently using Kerberos - just the agent part, as in just recording continually on 1 camera. It's basic but it works fine.

Thanks for reporting, could you report your issue in our GitHub repo? https://github.com/kerberos-io/agent/issues. Might be issuer to follow up, as it looks like something is going wrong reading the RTSP stream.

To discover the "ways" how you can deploy an agent, we have created a dedicated directory for it: https://github.com/kerberos-io/agent/tree/master/deployments

Hey all, we have been working hard on documenting the new Kerberos Agent. You'll find a good starter guide here -> https://github.com/kerberos-io/agent

Looking for zoneminder and kerberos.io surveillance systems, to be run on a fanless or miniPC system like Intel NUC i3 or i5 (suggestions heavily apprecitated!).

See also https://kerberos.io/ - It gives a nice UI for a single camera (can be remote) and stores motion, etc.