VoronMods
Mods I have created for my Voron printer (by kejar31)
Stealthburner-Umbilical-mod
By Markus-1984
VoronMods | Stealthburner-Umbilical-mod | |
---|---|---|
7 | 2 | |
126 | 14 | |
- | - | |
0.0 | 4.6 | |
over 1 year ago | almost 2 years ago | |
GNU General Public License v3.0 only | - |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
VoronMods
Posts with mentions or reviews of VoronMods.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-10-26.
-
Users of BTT SB2209/SB2240 - What are you using to mount the back end of the wire to the gantry?
kejar31 has an A-Drive umbilical mount as part of his CB-C2 mod. It's designed for larger wire, but should work with minor modifications.
-
Serial Request: V2.4 - blender#8476
the mod is an ebb36 mount with a small cooling fan and cable glands CB-C2 by kejar31
-
Do they make short dupont connectors?
I am switching over to an EBB36 on my V2.4 and I want to use to use the CB-C2 cover ( https://github.com/kejar31/VoronMods/tree/main/CB-C2) but I am running into clearence issues.
-
Serial Request: Voron 2.4 R2 350mm. Discord: Drewinator#3664
I didn't design it. I just meant I added it to my build. I got it from here: https://github.com/kejar31/VoronMods/tree/main/CB-C2
-
Serial Request Voron Trident 300mm jrubiks1209#3798
the umbilical on the A motor is on printables as you said, and the CB-C2 is https://github.com/kejar31/VoronMods/tree/main/CB-C2
-
How does one know what is the best configuration to build?
I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.
-
Serial Request - Voron 2.4 - Discord Teol037#2025
toolhead using CB-C2 along with lgx-lite cw2 mount
Stealthburner-Umbilical-mod
Posts with mentions or reviews of Stealthburner-Umbilical-mod.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-09-16.
-
How does one know what is the best configuration to build?
I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.
-
What gauge wire do I need if I want to run some extra wires to the printhead?
Yes. One of the EBBs and the U2C. If you're running a Stealthburner, I personally prefer this mod: https://github.com/Markus-1984/Stealthburner-Umbilical-mod.
What are some alternatives?
When comparing VoronMods and Stealthburner-Umbilical-mod you can also consider the following projects:
Voron-2-Mods - All my mods at one place
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
VoronUsers - Voron Community mods