Voron-Trident VS Voron-Hardware

I like to use KIAUH to install Klipper on the host. The Klipper documentation has instructions on making and flashing the part that comes on the MCU. And the Voron GitHub has sample configs you can use to get started.

If I can recommend - secure those wires when they exit X chain, else they will break in chains. print this https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Gantry/chain_wire_anchor_3hole_x2.stl put it under the chain end piece and use ziptie to tie wires to it. also, the Y cable bridge has a channel where you can put those wires into it, and secure them with zipties. Do not leave them strained like this.

Any chance you could tuck the wiring of A and B motors to 2020 slot and use slot cover, or few of these clips? https://www.thingiverse.com/thing:2246832 or just stock ziptie anchor points https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl It will look a bit better IMO.

Hello, I am not sure what's going on with your back if the gantry wiring. Can you tuck those wires in 2020 extrusion, and secure those with these little clips or print few of these anchors and use zipties? It will move them out of the way, decreasing risk of them getting caught into something. All wires on flying gantry go to A motor mount wnd then they enter Z chain -> to electronics compartment.

Another one - ziptie your wires where they enter drag chains. You can print one of these and put under drag chain end when plastic part does not have holes for pulling zipties through: https://github.com/VoronDesign/Voron-Trident/tree/main/STLs/Gantry Tie it down on one side, then push wires from other side of the chain, pull them, and try to find some middle point between where they move in chain. Then ziptie it there. This will ensure they are not moving around in chains, which will cause them rubbing, and possibly breaking when they bunch up or tangle.

There's a model for holding Wagos on bed extrusion https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Z_Assembly/wago_221-412_mount.stl

for the wiring goind from left B motor on gantry, you can tuck the cable in the 2020 extrusion groove and secure it with something like this https://www.thingiverse.com/thing:2246832 This clip from Trident repo https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl is also pretty useful to ziptie wires around the frame, inside electronics compartment for example.

No problem, yeah bad luck that you just ran out of connectors :-) Maybe just print few of these https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl and tie the cables down on the bottom of crossbeam for now.

Looks OK, but I am not sure what's going on with cables on the right side around A motor. Any chance you could tuck them under 2020 profile cover or ziptie them? You can print a few of there https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl or https://www.thingiverse.com/thing:2246832

Hello, the toolhead wiring may require few finishing touches. Ziptie those wires as close to the toolhead as possible, or use a wiring cover. If the stock one is small, you can use some of these for toolhead PCBs which are larger. https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs/Clockwork/Covers

That would be this one https://github.com/VoronDesign/Voron-Hardware/tree/master/V0-Umbilical/

I'm trying to setup the V0 display on my V0.2 but I get an error when trying to flash klipper to it. I'm following this guide and it shows up correctly with 'lsusb' but at step 9 it gives me this error. Can anyone tell me what I'm doing wrong? I'm using the BTT Pi V1.2 and an SKR Pico.

Hello, please, is there any chance to tidy up the wiring on Afterburner toolhead a bit? I believe there should be a shorter standoff available for Afterburner toolhead PCB, and the PCB cover can be found here https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover or here https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs

Hello, the toolhead wiring could use few finishing touches ... any chance you could ziptie those wires a bit closer to the toolhead, or ven better put a wiring cover? If the default one is small, you can use for example this one for toolhead PCBs but it works well for Microfit connectors too https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover or https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs/Clockwork/Covers

Hi, yes you can as stated earlier by u/rgar132 Alternatively you can also get Klipper Expander, it's a small MCU which will provide few more connectors for various purposes. https://github.com/VoronDesign/Voron-Hardware/tree/master/Klipper_Expander I got mine from Ali if you do not have option to have it made by PCB manufacturer, but I am sure few vendors have those as well.

Firstly, on the guide: https://github.com/VoronDesign/Voron-Hardware/tree/master/Daylight it mentions that the sticks need 24v but on the PCB's it says that they are 5v (https://imgur.com/a/cl4vzjY) and im not sure what to go for here.

The toolhead wiring requires some finishing touches too. Ziptie those stray wires to the rest of the bundle, or hide those under cable cover. If the stock is too small, use one of the larger alternatives like this one or some of these.