Voron-Trident Alternatives

Voron-Trident reviews and mentions

• Potential new Voron user
  2 projects | /r/VORONDesign | 16 May 2023

  I like to use KIAUH to install Klipper on the host. The Klipper documentation has instructions on making and flashing the part that comes on the MCU. And the Voron GitHub has sample configs you can use to get started.

• Serial Request - LDO Trident 300mm - H4kunaMatata#5589
  1 project | /r/voroncorexy | 8 Apr 2023

  If I can recommend - secure those wires when they exit X chain, else they will break in chains. print this https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Gantry/chain_wire_anchor_3hole_x2.stl put it under the chain end piece and use ziptie to tie wires to it. also, the Y cable bridge has a channel where you can put those wires into it, and secure them with zipties. Do not leave them strained like this.

• serial request - voron trident 350mm - Hylton#2756
  1 project | /r/voroncorexy | 3 Mar 2023

  Any chance you could tuck the wiring of A and B motors to 2020 slot and use slot cover, or few of these clips? https://www.thingiverse.com/thing:2246832 or just stock ziptie anchor points https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl It will look a bit better IMO.

• V2.4r2 Serial Request - Stevan#0496
  1 project | /r/voroncorexy | 12 Feb 2023

  Hello, I am not sure what's going on with your back if the gantry wiring. Can you tuck those wires in 2020 extrusion, and secure those with these little clips or print few of these anchors and use zipties? It will move them out of the way, decreasing risk of them getting caught into something. All wires on flying gantry go to A motor mount wnd then they enter Z chain -> to electronics compartment.

• Trident LDO Kit - Trouble squaring frame. What am I doing wrong?
  1 project | /r/VORONDesign | 20 Dec 2022
• Serial request V2.4r2 300mm Discord: Austenite#5308
  2 projects | /r/voroncorexy | 5 Nov 2022

  Another one - ziptie your wires where they enter drag chains. You can print one of these and put under drag chain end when plastic part does not have holes for pulling zipties through: https://github.com/VoronDesign/Voron-Trident/tree/main/STLs/Gantry Tie it down on one side, then push wires from other side of the chain, pull them, and try to find some middle point between where they move in chain. Then ziptie it there. This will ensure they are not moving around in chains, which will cause them rubbing, and possibly breaking when they bunch up or tangle.

• Serial Request - Voron Trident - alexmay#7047
  1 project | /r/voroncorexy | 2 Aug 2022

  There's a model for holding Wagos on bed extrusion https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Z_Assembly/wago_221-412_mount.stl

• Serial Request - Voron 2.4 300mm - Shau Chen#1646
  2 projects | /r/voroncorexy | 9 Jul 2022

  for the wiring goind from left B motor on gantry, you can tuck the cable in the 2020 extrusion groove and secure it with something like this https://www.thingiverse.com/thing:2246832 This clip from Trident repo https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl is also pretty useful to ziptie wires around the frame, inside electronics compartment for example.

• Voron V2.4 350mm Serial Request LostG#1920
  1 project | /r/voroncorexy | 6 Jul 2022

  No problem, yeah bad luck that you just ran out of connectors :-) Maybe just print few of these https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl and tie the cables down on the bottom of crossbeam for now.

• Voron Trident Serial Request AnonymousAsian#9857 (discord)
  1 project | /r/voroncorexy | 5 Jul 2022

  Looks OK, but I am not sure what's going on with cables on the right side around A motor. Any chance you could tuck them under 2020 profile cover or ziptie them? You can print a few of there https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl or https://www.thingiverse.com/thing:2246832

• A note from our sponsor - WorkOS
  workos.com | 25 Apr 2024

  The APIs are flexible and easy-to-use, supporting authentication, user identity, and complex enterprise features like SSO and SCIM provisioning. Learn more →