RPi4 VS BorgBackup

Correct. It does not as shipped. However, the use of this project will bring the firmware into system ready spec, so it can boot with a standard aarch64 UEFI image: https://github.com/pftf/RPi4

are you using the uefi firmware from https://github.com/pftf/RPi4 or are you trying to boot through the gpio serial header?I don't think the pi can boot on its own through uboot unless your using a serial/usb connection

Looks like you can use Grub on UEFI ARM systems, but Raspberry Pi isn't natively running UEFI. https://github.com/pftf/RPi4

The rpi4 has uefi firmware available, this allows you to boot any generic uefi aarch64 image, you no longer need rpi specific images.

https://github.com/pftf/RPi4

Straight out of the box, the image wouldn't boot, said that start.elf was invalid, so I went to https://github.com/pftf/RPi4/releases as suggested in the Readme.md file in the EFI partition. I installed that (version 1.34) over the existing EFI partition and tried again. That booted up the kernel, but it apparently died when it enabled the interrupt controller. The last messages are about armgic0.

Maybe similar discussion on github:

You can use these firmware images for UEFI as well as install with the arm ISO. I didn't have graphics acceleration that way, but it might be an easy fix.

I'm guessing these are not SystemReady certified with UEFI firmware and require "bespoke" preinstalled arm images?

https://www.arm.com/architecture/system-architectures/system...

https://developer.arm.com/documentation/102677/0100/UEFI-req...

I have three SystemReady arm devices and it's pretty awesome to be able to just boot an aarch64 live ISO and install. The experience is the same for running vms via ESXi arm edition.

Nvidia Jetson AGX Xavier - https://developer.nvidia.com/embedded/downloads#?search=uefi

Honeycomb LX2 - https://github.com/SolidRun/lx2160a_uefi

RPI4 - https://github.com/pftf/RPi4

It can be tedious building/provisioning the firmware but once complete they are ready for any aarch64 uefi iso.

What is annoying however is when distros don't ship an aarch64 uefi iso - but instead choose to build a zillion device specific "preinstalled" arm images. (looking at you manjaro)

The list of supported devices for ESXi arm edition is a great place to start for identifying options and is constantly updated.

https://flings.vmware.com/esxi-arm-edition

  Raspberry-Pi-4

The only reason why I am was trying to build the image was because I wanted to move stuff as mainline as possible and was worried that any installation made with the help of RPi4 UEFI firmware would stop booting after a while.

Most ARM hardware is cellphones, raspberry pi and the Mac M1, which certainly aren't that type.

But a lot of ARM hardware is that type. The keywords are SBSA / SBBR / SystemReady. If your hardware is SBBR compatible then Fedora and Ubuntu's ARM64 iso, and Windows ARM64, downloaded from their website, will at least boot fine (drivers are a different question as always).

There's a good list of supported hardware in the lower half of https://community.arm.com/arm-community-blogs/b/architecture... . Many systems from Avantek, Gigabyte, NXP, Marvell, Solidrun etc are standardizing on this way of booting.

DeviceTree is low-level enough that you can implement UEFI on top of it. There's a UEFI port for the Raspberry Pi 4 at https://rpi4-uefi.dev/ that produces an SBBR layer, allowing it to boot any off-the-shelf ARM64 SBBR distro.

I started using Nextcloud for file/contact/calendar syncing a few years, and have gradually moved most of my digital life into it. Documents and photos, but also scripts to automatically set some things up for me when I do a fresh install of Linux (I've been playing around with a few different distros lately). The only thing that doesn't live in Nextcloud are some old DVD rips, and that's mostly due to "haven't gotten around to it yet". Besides those, if it's not in Nextcloud, it's not something I care too much about losing if a disk were to fail.

My Nextcloud instance is then backed up to another drive on the same machine plus two off-site locations - an old server I still run at my parents' house, and and external HDD my friend let me plug in to his server. The on- and off-site backups are done using `borg` (https://www.borgbackup.org/), which does reduplication and encryption (with the keys backed up in 1Password).

I've been meaning to set up an automated restore on one of the offsite servers - a script to automatically unpack the latest backup, set up a fresh DB, and make things read-only - firstly to verify that the backups are functional and complete, but also as a backup in case my home server or home internet goes down. I know in _theory_ I've got everything I need in the backups to do a full restore, but I can't recall the last time I actually tried it out...

i use - and recommend - "borgbackup": for example with the "vorta" graphical frontend

* https://www.borgbackup.org/

* https://vorta.borgbase.com/install/windows/

just my 0.02€

I used this many, many years ago but switched to Borg[0] about five years ago. Duplicity required full backups with incremental deltas, which meant my backups ended up using too much disk space. Borg lets you prune older backups at will, because of chunk tracking and deduplication there is no such thing as an incremental backup.

[0] https://www.borgbackup.org/

Currently, I'm auto-backing it up with borg (push mode) through wireguard tunnel to NAS behind ISP's CGNAT. The borg takes care of deduplication in SQL file, so incremental update (even in append-only mode) is very small for PostgreSQL dump.

Borg 2 has been in development for nearly a year and a half [1] and may probably be released early next year, i.e., early 2024 (just a guess, seeing that even RC1 is not yet released and seems to have a lot of work to be done).

Does anyone know how Borg 1.x and 2 would compare to Kopia?

[1]: https://github.com/borgbackup/borg/issues/6602

You could use borgbackup.