MajorCore
MightyCore
| MajorCore | MightyCore | |
|---|---|---|
| 1 | 5 | |
| 38 | 618 | |
| - | - | |
| 6.4 | 6.9 | |
| 4 months ago | about 1 month ago | |
| C++ | C++ | |
| GNU Lesser General Public License v3.0 only | GNU General Public License v3.0 or later |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
MajorCore
-
Development using an ATMega162-16PU assistance needed badly. heh
I've already added the 162 to the IDE using information garnered from here and other places. But the problem lies in the circuit. I'd like to set up a socketed 40-PDIP version of an Uno-like PCB with USB, so that when testing and programming is done, I can pull the 162 out, slap it into the project and run with it, as one does.
MightyCore
-
Fast Led Multiple Colour Pallets in a State Machine
I am working on a project using the WSB2812B LED strip, with a ATmega644A using the MCUdude/MightyCore plug in (https://github.com/MCUdude/MightyCore). I am using Fastled 3.3.3 with Ardunio 1.8.13 on Windows 10 and is using code based off "ColourWavesWithPalettes" (https://gist.github.com/kriegsman/8281905786e8b2632aeb).
-
I need a push...ATMEGA1284P
However, what I ended up doing was using MightyCore as my AVR core instead of trying to use it outside of the Arduino IDE.
-
No hardware SPI pins defined (Help Please)
Morning I assumed that you've seen this issue? https://github.com/MCUdude/MightyCore/issues/235
-
I have a graduation project where I need to build an arduino board completely from scratch. We are asked to chose a microcontroller that was never been used on an arduino before just like the “Atmega 1284”. What do you guys think will it be hard, and if you have any advice
https://github.com/JChristensen/mini1284 https://github.com/MCUdude/MightyCore
-
Burning a bootloader to atmega32.
I made a DIY microcontroller featuring atmega32 16-au, and I'm trying to burn a bootloader to it using an Arduino UNO. I'm using MightyCore library and this is the schematic. I upload Arduino as ISP sketch to my Arduino, connect the atmega32, put a 22uF electrolytic capacitor between ground, and reset on Arduino and I get this error:
What are some alternatives?
FastAccelStepper - A high speed stepper library for Atmega 168/328p (nano), Atmega32u4, Atmega 2560, ESP32, ESP32S2, ESP32S3, ESP32C3 and Atmel SAM Due
MiniCore - Arduino hardware package for ATmega8, ATmega48, ATmega88, ATmega168, ATmega328 and ATmega328PB
ATtiny84-TinyCalibrator - OSC Calibrator and High-Voltage Fuse Resetter for 8-Pin ATtinys
Fast - Fast IO compatible with library making for Arduino.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
ServoEasing - Arduino library to enable smooth servo movement.
mini1284 - A minimal breadboard-friendly design for the ATmega1284P MCU