Arduino_Core_STM32
rc-switch
Arduino_Core_STM32 | rc-switch | |
---|---|---|
10 | 12 | |
2,642 | 1,880 | |
1.2% | - | |
9.3 | 0.0 | |
6 days ago | about 1 month ago | |
C | C++ | |
GNU General Public License v3.0 or later | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Arduino_Core_STM32
-
What is the difference between between Arduino and STM32
There's nothing stopping Arduino releasing an STM32-based dev board - but they simply haven't yet, and there's stacks of stm32 boards around that you can add an Arduino support core for if you like.
-
From Arduino to STM32CubeIDE
https://github.com/stm32duino/Arduino_Core_STM32 look this
- RF module Fs1000A with Stm32
-
SKR Mini E3 V3 TFT35 Firmware Compiling Issue
It shows this https://github.com/stm32duino/Arduino_Core_STM32/archive/main.zip getting to 97% then skipping to the next unpacking, then it seems to fail thereafter.
- Arduino for STM32
- Wiring up a simple ST7789 to an F767ZI - or really any nucleo
-
STM Microcontrollers vs Arduino Microcontrollers
You can program an STM32 MCU with Arduino, just add the community developed board definitions and HAL to the Arduino IDE.
-
Are any of the components worth salvaging off these temp data loggers?
If the mcu disables itself after it's one use you could program it via arduino to reset it or give it a new purpose. Reprogramming the chip will likely be the best use, those components are only a few cents it's more effort than it's worth to save them. Repurposing the board is what I'd try to do, weather that's via replacing the stm32 or reprogramming it is up to you.
-
Stm32f103c8 bluepill hmc5883l compass problems
I am using the stm32duino core for the Arduino Ide (https://github.com/stm32duino/Arduino_Core_STM32). My settings are the following:
-
New Microcontroller launched by the R Pi foundation: Raspberry Pi PICO (4$)
(official Arduino HAL) STM32
rc-switch
- Looking to make a wireless mic button for Walkie-talkie, do they make a receiver that can be wired into a button, or do I need an arduino on each side?
-
RF module Fs1000A with Stm32
It really depends too on what the transmitter is sending, do you have any information on the transmitter device? You can try rc-switch which supports interpreting multiple protocols/timings: https://github.com/sui77/rc-switch
-
Help please: Listening to 433mhz with RC-Switch but not getting any serial output
According to https://github.com/sui77/rc-switch Rc-Switch says they support the following chipsets:
- I can't get the 433MHz rf receiver to work, it just spits out "random" pulses.
- Anyone know how to hook up these physical buttons so they can be triggered by an ESP32?
-
315mhz receiver advice
According to the output from https://github.com/sui77/rc-switch/, the protocol is 11, which correlates to HT12E.
-
I need help figuring out why I can’t clone the rf signal from the Arduino (rf sender) to the remote. I am using the SendDemo example from rc-switch library
/* Example for different sending methods https://github.com/sui77/rc-switch/ */#include RCSwitch mySwitch = RCSwitch();void setup() { Serial.begin(9600); // Transmitter is connected to Arduino Pin #10 mySwitch.enableTransmit(10); // Optional set protocol (default is 1, will work for most outlets) mySwitch.setProtocol(1); // Optional set pulse length. mySwitch.setPulseLength(370); // Optional set number of transmission repetitions. // mySwitch.setRepeatTransmit(15); }void loop() {/* using decimal code */ mySwitch.send(16736113, 24); delay(350); //mySwitch.send(5396, 24); //delay(1000); ;}
-
simple R/C communication using 433mhz and ATTINY85 [help wanted]
-in my esp32 setup i use digitalPinToInterrupt(MyPinNumber) to make it easier to use the correct pin maybe that helps in your case too. -According to the comments here it should be working on the attiny85, maybe you can adapt some of their examples https://github.com/sui77/rc-switch/issues/143 -getReceivedValue() returns an unsigned long for me, maybe there's a conversion problem in your code.
-
My uncle recently built a PC and I don’t understand it, was wondering if anyone can take a shot at figuring out how it works. (Sorry, I’m a newbie)
// library from https://github.com/sui77/rc-switch/ # include RCSwitch mySwitch = RCSwitch(); mySwitch.enableTransmit(10); // pin 10 // do your own logic detection, but these send the light commands: mySwitch.send(4853521, 24); // change to white color mySwitch.send(4853524, 24); // blue mySwitch.send(4853523, 24); // red
-
Control radio controlled switches with a raspberry pi pico
Hi reddit, I just ported the awesome rc-switch library to the raspberry pi pico, so now you can control radio controlled switches using cheap 433Mhz radio modules. Previously it only worked on arduinos and raspberry pis. Check it out
What are some alternatives?
stm32-bootloader - Customizable Bootloader for STM32 microcontrollers. This example demonstrates how to perform in-application-programming of a firmware located on an external SD card with FAT32 file system.
rc-switch-pico - Raspberry Pi Pico lib to operate 433/315Mhz devices like power outlet sockets. Ported from rc-switch for arduino
MCUDEV_DEVEBOX_F407VGT6 - MicroPython board definition for the MCUDev DevEBox STM32F407VGT6 board
pico-onewire - Raspberry Pi Pico OneWire Library
pico-examples
markisol - Arduino control for Markisol protocol 433.92MHz window shades and BF-101, BF-301, BF-305 remotes
FunctionGeneratorCortexM4_HW - A function generator powered by ARM Cortex M4
bf-305-remote-api - Send markisol commands from rest on Raspberry Pi
Arduino_STM32 - Arduino STM32. Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards
inkplate6 - Inkplate6 project with time, date, weather and upcoming Google calendar events
stm32-makefile - A small, simple example project demonstrating how to use an STM32 microcontroller with GNU Make, ARM GCC, and ST-Link/OpenOCD
STM32F746-CMSIS-Chained-Timers-Demo - STM32F746 demo of 4 chained timers starting each other in various ways