3W6 VS qmk_firmware

The rest is pretty simple - XIAO controllers, wired/wireless support, 1 rotary encoder, reversible PCB, TRRS or USB-C connection. Very low profile - no bottom plate, no hotswap. Thick top plate so switches are soldered almost flush with the PCB (thanks 3w6 for inspiration). Knob for the low profile encoder is taken from KLOTZ by u/_GEIST_. Unfortunately it was a bit too wide so I had to sand down couple of mms.

For what it's worth, I'm on a 3w6. Shout out to weteor for the inspiration for this one.

As 2 corne and 1 sweep owner , i can tell you also have the 3rd option if you are fine with choc switches and live in Europe 3w6. https://github.com/weteor/3W6 It has a middle layer and on board mcu, an completely enclosed. I have no worries when I put it to my backpack;)

So, purely out of my own needs, and since the Sweep doesn't quite cover that, I'd love a 3W6 or a Roost. Or even a Rae-dux.

There is the Weteor 3w6

Checkout the 3w6, which is a 3x5+3 split i.e. the same amount of keys as the GergoPlex. You can print the PCB with SMT assembly done for you, so all that's left is to solder on your choice of switches. JCLPCB just happened to have all the components available and in the [github repo](https://github.com/weteor/3W6) there are some discussion/instructions on ordering from them. A slight issue is that you get at least 5 sets of PCBs and at least 2 with full SMT assembly, so you may want to sell the extras on the mech marketplace.

Hi all, I want to build a 3W6 keyboard. https://github.com/weteor/3W6 I need some help & advice please. Don't laugh at my beginner stupidities!

3W6 one of the cheapest build I have seems https://github.com/weteor/3W6

I only use keyboards running QMK or ZMK, so:

My Caps Lock key is a Control/Escape key (when tapped it behave like a Escape, when hold it's Control), and my left Control is a one shot layer switch key [1], which means I tap LCtrl once, and then press Caps Lock + 5 to get Ctrl+F5. Doable with single hand and more ergonomic as I have an unusually small hand.

[1] https://github.com/qmk/qmk_firmware/blob/master/docs/one_sho...

I agree that reduced finger movement is a crucial step in achieving typing efficiency. This is nicely solved by mod tap modifiers in QMK/ZMK[1] where key acts as a char when tapped and as a layer while pressed.

[1]: https://github.com/qmk/qmk_firmware/blob/master/docs/mod_tap...

Separate wireless controller, see the glue code at [0]

[0]: https://github.com/qmk/qmk_firmware/compare/master...nuphy-s...

If you have a keyboard that runs QMK firmware[0] with the VIA[1] feature enabled[2], then there is a convenient testing app available from the same place you customize your keys [3].

[0] https://qmk.fm/

I made a layout that I'm happy with. Spanish is my native language, so it has characters like the accents and 'ñ', but it's meant to be used for programming as well. Visual Studio uses a lot of Ctrl and Ctrl + Shift shortcuts, so I left them in the same place as the default Corne layout so I can press them both with my pinkie finger. Perhaps some of the ideas are useful to you.

Also, it would be possible to do this for the RP2040. However, it needs some work to get working. but for example: https://github.com/qmk/qmk_firmware/pull/20999

Ok, it's an ST7735, not too different from the ST7789. You should be able to get running by looking at their files in the QMK repo and going from there. You should also check their resources page.