strayr-k-macros
useful macros to extend the functionality of klipper (by strayr)
Gasherbrum-K3
Open Air or Fully Enclosed, Small Format, Moving Bed, CartesianXY, FDM 3D Printer with Direct Drive Extrusion System (by Annex-Engineering)
strayr-k-macros | Gasherbrum-K3 | |
---|---|---|
36 | 2 | |
126 | 353 | |
- | 2.8% | |
3.8 | 5.5 | |
5 months ago | 8 days ago | |
GNU General Public License v3.0 only | GNU General Public License v3.0 or later |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
strayr-k-macros
Posts with mentions or reviews of strayr-k-macros.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-05-31.
- Bed Management Macros from Strayr
- Which custom macro of yours are you most proud of, or find most useful?
- Smart movement of print head after print complete?
-
Should I be concerned?
I use this macro to do square the gantry against the top frame You should only do this if you have adjustable current for your stepper drivers ([tmcxxxx] sections in your config for stepper_z and stepper_z1 drivers) You'll also want to make sure your stepper_z.position_max is just before the gantry would contact the frame.
-
Z offset questions
I've added it into my LCD menu https://github.com/strayr/strayr-k-macros/blob/main/improved_menu.cfg, but beware, some of the menuitems pull in macros from other parts of the package. You may find the whole lot useful, read the docs. it needs some updating and perhaps the probe menu splitting into a standalone file.
-
Dual boards for same printer
I use u/strayr-k's macro for this: mechanical_level_tmc2209.cfg
-
Using bed leveling probe for bed tramming
I always use strayrr-k's mechanical gantry calibration macro to tram the gantry against the frame before using screws_tilt to level the bed.
-
pretty proud of this bed leveling job on my ender 3.i fully expected a bit of warp but I'm super happy with this.
Last note, the G34 macro I use is this one. Works really well on my dual Z setup (one driver for both steppers). I've noticed my Ender3 X gantry likes to set itself just a bit off-kilter when steppers are disabled, so I run a G34 at every startup to ensure it stays level as long as the motors are enabled.
-
Change to Stealthchop mid-print
you can try this https://github.com/strayr/strayr-k-macros/blob/main/M204.cfg but it can cause crashes if you have gcode with lots of accel changes, I encountered this on small mmu prints with lots of very short perimeters but it might be ok.
-
PID tuning macros
I use mech_gantry_cal.cfg a lot, but that only applies if you use dual z steppers and dual z drivers. This macro will bump the gantry against the z_max to straighten it against the frame and eliminate any drift between the drivers.
Gasherbrum-K3
Posts with mentions or reviews of Gasherbrum-K3.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-08-28.
-
Voron 0.1 - How frequent do folks need to re-level the bed when using different plastics?
Also, I hate to recommend a not voron based build but https://github.com/Annex-Engineering/Gasherbrum-K3 is my next printer. Small but has the volume you want, and is the fastest FDM printer I’ve seen. Not as user friendly to build as a voron from what I’ve seen playing with the idea. Not that I expect it to be a problem.
-
Annex K3 Beta - You've seen 25k accel and 300mm/s. Now magnetic docking probe and articulating nozzle brush.
Hey that's a nice printer. I had a look at https://github.com/Annex-Engineering/Gasherbrum-K3 It reminds me of a Voron crossed with a Hypercube.
What are some alternatives?
When comparing strayr-k-macros and Gasherbrum-K3 you can also consider the following projects:
Klipper-Adaptive-Meshing-Purging - A unique leveling solution for Klipper-enabled 3D printers!
klipper-web-control-docker - Klipper with Moonraker shipped with Fluidd and/or Mainsail
klipper-prusa-mk3s - Structured Klipper config for Prusa MK3s 3D printer
Print-Tuning-Guide
Tiny-M - Tiny-M R 5
VoronUsers - Voron Community mods
klipper-backup - Klipper backup script for manual or automated GitHub backups. Lightweight, pragmatic and comfortable.
kiauh - Klipper Installation And Update Helper
zippy-klipper_config - Zippy Klipper Config
printcfg - A suite of macros to enhance the klipper experience
klipper - Klipper is a 3d-printer firmware
strayr-k-macros vs Klipper-Adaptive-Meshing-Purging
strayr-k-macros vs klipper-web-control-docker
strayr-k-macros vs klipper-prusa-mk3s
strayr-k-macros vs Print-Tuning-Guide
strayr-k-macros vs Tiny-M
strayr-k-macros vs VoronUsers
strayr-k-macros vs klipper-backup
strayr-k-macros vs kiauh
strayr-k-macros vs zippy-klipper_config
strayr-k-macros vs printcfg
strayr-k-macros vs klipper