openmiko VS scrypted

Have a Wyze Cam V2 running openmiko. I can pull the feed via the camera's IP, but Klipper (Fluidd, Mainsail on BTT CB1) shows like below. Additionally, moonraker-timelapse throws an error. This was working fine until I tried Hyperlapse. Now I can't wrap my head around this

I'm running MainsailOS, and a Wyze cam v2 running openmiko. I have Tailscale installed on the Pi for remote access. In Mainsail config, I have the camera configured via private IP. When I access the web control panel externally, I do not get video output. Is there a way to get this to work? I do not think there's a way to connect the Wyze cam to my tailnet.If it's not possible, have any good recommendations for a good, cheap, wide-angle (110 degrees FOV or better) camera I can purchase? I wouldn't want to spend more than $25 for one. Quick search yielded this one, but don't know if there's a Klipper-community recommended one that everyone uses.

you wish lol. the mod allows you to get highest possible resolution video out of it without all the compression pixelation. its super easy to install. but it does take a little bit of linux knowledge to edit config files and stuff. heres the link if interested: https://github.com/openmiko/openmiko

I bought a used Wyze Cam V2 relatively cheap and installed OpenMiko on it for example.

I have a WyzeCamV2 running OpenMiko firmware, which supports (and I have configured for) H264 RTSP streaming. I can view the video stream through VLC with the url rtsp://192.168.1.199:8554/video3_unicast. I am executing the command docker run -p 8081:80 --name mycamera -e AGENT_CAPTURE_IPCAMERA_RTSP="rtsp://192.168.1.199:8554/video3_unicast" kerberos/agent:latest on my host. The agent seems to run fine and I can connect via browser. With our without AGENT_CAPTURE_IPCAMERA_RTSP... set, I cannot add the RTSP stream; no cameras show attached and when I try to connect one via dashboard->settings, it just spins. The logs aren't really helpful (see below).

OpenMiko is one example.

That's why I only use cameras flashed with open firmware: https://github.com/openmiko/openmiko

If all else fails, you can flash different firmware and use them locally. I'm using [OpenMiko](https://github.com/openmiko/openmiko) on my Wyze Cam v1 (I'd assume there's a similar open-source project for the v3), and Wyze themselves publishes an RTSP firmware. Without a bit of technical know-how and some supporting hardware (namely a router than supports OpenVPN) you won't have access to the stream off your local network, but you can stream locally with VLC Player.

lazyweb: https://github.com/koush/scrypted (regrettably the licensing is "it depends" https://github.com/koush/scrypted/blob/v0.93.0/LICENSE.md#li... )

and don't overlook that user's other repos, as seems like there are quite a few fun things in there: https://github.com/koush?tab=repositories

I have taken a look at the page for debugging steps for Homekit recording and haven’t played with any setting mentioned there.

Unfortunately the options for HKSV doorbells is fairly limited. The Logitech circle view Doorbell looks like the best candidate but it has a spotty review history, with the biggest complaint being it breaking in direct sunlight.

I’m about to buy some cameras and I’m thinking of just buying Nest and using https://scrypted.app to bridge to HKSV.

In the demo video linked to from the Scrypted Github repo, the author has some kind of a delivery box (visible in the top camera), with a camera inside the box in night vision mode, able to report on whether there’s anything in the box. Does anyone know how this setup was achieved, or have done something similar to combine a camera with a closed delivery box?

You can migrate the scrypted setup with this: https://github.com/koush/scrypted/wiki/Scrypted-Backup-and-Restore

I see two options, both from brands that seem to be well-received on the brand report card.

You might want to try setting them up with Scrypted then use the plugin to get them into Homebridge.