grbl
cncjs
grbl | cncjs | |
---|---|---|
90 | 29 | |
3,939 | 2,190 | |
0.8% | 1.1% | |
0.0 | 2.9 | |
3 months ago | 19 days ago | |
C | JavaScript | |
GNU General Public License v3.0 or later | MIT License |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
grbl
- Potreste aiutarmi a capire il modello di questa macchina ad incisione? (non รจ laser)
- Has anyone programmed a professional CNC or Laser cutting machine with PLC technology? What are the key points about it?
-
H-bot pen plotter imprecise
The other thing to consider is the $12 config in GRBL itself: Arc tolerance. Drawing circles is EITHER a long series of small line segments, OR an "arc". If this problem only effects arcs: you can likely limit your search there.
-
limit switches convert 6090 2.2k cnc to grbl
You can use NO limit switches with GRBL. Here is some info. But NC is generally a better option because if there is a failure in a wire or connector, the circuit will open and stop the machine.
-
If I don't use Windows or Mac and only use Linux, will I run into a lot of compatibility issues?
Grbl is a firmware for Arduino based microcontroller dev boards. https://github.com/gnea/grbl/wiki Once programmed you stream the gcode to the grbl controller over USB. It's constrained by the limitations of the Arduino hardware or runs on but it's a great entry point to CNC machines. Note that a 32 bit grbl is under development but pre built control boards are still rare.
-
How to calibrate a GBRL CNC machine ?
The gnea/grbl GitHub Getting Started page spells all that out.
-
building my own laser measurement system for 3d measurements
This may not be a fit, but it may give you ideas for prototyping/software dev. I have prototyped various CNC/optical/medical projects using GRBL GitHub and a simple benchtop frame-gantry setup that I made from 80/20 and steppers.
-
Y axis wrong direction
To learn more: https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration
- Dead SO3 board
-
Is there a way in this software to reverse the direction of X and Y?
If it really is GRBL, you'll find most of the information you need at https://github.com/gnea/grbl/wiki and the $ commands at https://github.com/gnea/grbl/wiki/Grbl-v1.1-Commands
cncjs
-
Help
I believe the Tool Change command is supported by: gSender or cncjs.
-
Can I connect my laptop to my desktop CNC with a bluetooth usb dongle?
Get a raspberry pi, https://www.raspberrypi.org/, throw UGS https://winder.github.io/ugs_website/ or cnc.js https://cnc.js.org/ on it.
-
If I don't use Windows or Mac and only use Linux, will I run into a lot of compatibility issues?
I use https://cnc.js.org/ to send g-code to the machine, this uses web page interface to set up the machine.
-
Running CNCJS on raspberry pi - other computers don't see the job
https://github.com/cncjs/cncjs/issues/431 ?
-
Must have Self-Hosted Developer Tools
CNCjs - For CNC, same as above but for my CNC router, though I would never trust my CNC to run when I'm not physically close by ha ha so this hasn't been exposed to my OpenZiti network.
-
how to control your laser engraver with a raspberry pi?
I think cncjs is what you're looking for: https://cnc.js.org/
-
Laser engraver continually alarming!
Can you try with a different gcode sender software (cncjs), to see if you can Reset (red button) and Unlock (orange button)?
-
ortur Laser Master Pro 2 SF not burning
6 - Alternative, Save the gcode and use a g-code sender (example: cncjs). Notice: a g-code sender needs to know where is the 0,0 position/the start position, so in LightBurn select the start position "Current Position" and select the appropriate Job Origin. Save the gcode. On cncjs, move the laser to the "Job Origin" and zero both X and Y (the icon after the + on the Work Position). Click the blue Upload G-Code button, select your file and press the Play button to start the job.
-
Motors moving inconsistently
Software: bCNC, cncjs, a couple others
- Apple Silicon Is an Inconvenient Truth
What are some alternatives?
grbl-Mega - An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on an Arduino Mega2560
Universal-G-Code-Sender - A cross-platform G-Code sender for GRBL, Smoothieware, TinyG and G2core.
LaserGRBL - Laser optimized GUI for GRBL
Candle - GRBL controller application with G-Code visualizer written in Qt.
ESP3D - FW for ESP8266/ESP8285/ESP32 used with 3D printer
simple-gcode-generators - Simple LinuxCNC G-Code Generators written in Python
bCNC - GRBL CNC command sender, autoleveler and g-code editor
grbl-servo - grbl 0.9i with Servo motor support
ESP3D-WEBUI - A Web UI for ESP8266 or ESP32 based boards connected to 3D printers / CNC
grbl - An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on a straight Arduino
OpenBuilds-CONTROL - OpenBuilds CONTROL: Download from https://software.openbuilds.com