VoronUsers
VoronUsers
VoronUsers | VoronUsers | |
---|---|---|
3 | 347 | |
10 | 2,868 | |
- | 1.4% | |
2.6 | 8.8 | |
over 2 years ago | 2 days ago | |
GAP | OpenSCAD | |
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
VoronUsers
-
Probe comparison
I use a CR Touch with the CR Shell Mod and a modified MGN-12 SB carriage so that it fits in the stock probe slot. Started with unklicky-NG for a bit, but had too many issues with the dock flexing just enough during high temp prints that it wouldn't mount successfully unless I let everything cool down between prints.
-
How does one know what is the best configuration to build?
I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.
-
Ender 3 V2.. need hotend recommendations.
I'm planning on using the Afterburner by Voron Design that is on their 2.4r2 build (STLs here), with this mod to allow me to still use my CR touch.
VoronUsers
-
Serial Request - Trident 300 - Discord: orangetruth
270º Clamping Hinges
-
Re-did my Rook Legacy to Rook 2020. Lowered the Z and used 2020 extrusions for the frame to make it super stable. Threw in Klicky probe and CPAP cooling too 😁
Hotend is a Triangle Labs CHC Pro. Extruder setup is a mixture of a couple 😅 -mod of Mantis Toolhead to mount on MGN9C
-
Serial request | V0.2 | Discord: Hr_Ravn#7480
Stealth skirts by Maverick
-
Wire guides which I'm using to help with cable management on my 2.4 build
Those are a duct remix of this design, it is not yet posted since I need to install my wires to make sure no changes are needed. It will probably be uploaded in the next week.
-
Serial Request Voron Trident
I'm running a Chainflex umbilical cable + a beacon probe USB cable along the prebowden. I'm thinking about running the Bowden guide to help, I'm not pinching anything when I home the printer, but I'm looking to keep everything up and out of the way. https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Galvanic/Bowden_Tube_Guide
-
Finally reached 60C with my scavenged solution for bed fans. ASA is smooth!
Here is a good cfg to automate the fans
-
config issues
basically copied and pasted from here: VoronUsers/bedfans.cfg at master · VoronDesign/VoronUsers · GitHub with printer specific info bellow
-
Remix of Hartk1213's Voron2.4 GE5C Z Joint (available on Printables and TeamFDM)
Why don't you submit this to the vetted mods repository? https://github.com/voronDesign/voronusers
-
Silly question. How do you open bottom panel?
I swapped to these magnetic bottom panels and they are awesome!
-
Voron Trident 3D Printer Review - My experience with the Fysect Kit | igor'sLAB
I noticed that you mentioned being annoyed by the cable management (or lack of it) in the kit, which I think is probably not uncommon with many kits with some exceptions (LDO looks nice). That bothered me also, so I'm also working on something to help with cable management, which may also work with the Trident (a remix of these cable ducts).
What are some alternatives?
Voron-2 - Voron 2 CoreXY 3D Printer design
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
Voron-2-Mods - All my mods at one place
Klicky-Probe - Microswitch probe with magnetic attachement, primarily aimed at CoreXY 3d printers
Voron - This repository contain files related to modifications or experimentations I performed on parts of 3D Printers designed by the Voron team
Sherpa_Mini-Extruder - A smaller version of the sherpa extruder, direct and bowden supported
VoronMods - Mods I have created for my Voron printer
whopping_Voron_mods
Stealthburner-Umbilical-mod
klipper - Klipper is a 3d-printer firmware
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
Voron-Afterburner - VORON Afterburner Upgrade