crkbd
cantor
crkbd | cantor | |
---|---|---|
194 | 34 | |
4,891 | 557 | |
- | - | |
8.9 | 4.8 | |
6 days ago | 6 months ago | |
Makefile | ||
Creative Commons Attribution 4.0 | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
crkbd
- Problem with JLCPCB holes
-
Issues with backlight LEDs
Looks at the order here : https://github.com/foostan/crkbd/issues/96
-
Problems with a new low-profile corne
I followed this guide for the build (https://github.com/foostan/crkbd/blob/main/corne-classic/doc/buildguide_en.md)
-
Nice!view not working when leds are turned on?
Not sure which information you mean, but here goes. Nice!Nano v2 Pinout (shows Arduino pin mapping). Nice!View Getting Started (explains how to remap the CS pin for a non-native shield like Corne). The overlay file where "cs-gpios" is set for the nice_view_adapter in ZMK. If you look at the Corne Schematic, you'll see as shown in the labels in this image that the bottom two pins (B2, B4, B5, B6) don't appear to be used for a column, row, or the OLED header. But the only way to really verify is to pull the KiCAD file for your Corne version and check yourself. I think D0 ("Data") should work. It appears to go to an optional I2C connection.
- Accidentally ripped off solder pad
-
Corne, but with a wider thumb cluster and stronger column stagger?
Want to say the corne board drawings etc are available at https://github.com/foostan/crkbd as well, if you fancy learning kicad you might be able to tweak them yourself ... though that is definitely the deep end of things...
-
My Corne V3 Build
https://youtu.be/-E7KRnVCjq8 https://youtu.be/4bB9A1YYyII https://github.com/foostan/crkbd/blob/main/corne-cherry/doc/v3/buildguide_en.md
-
Frandestein: my first handwired custom keyboard
For the layout, I took inspiration from the CRKBD and the Boardsource's Microdox.
-
Only one LED works on each side
This is the numbered LED series from the Corne Classic Build Guide (https://github.com/foostan/crkbd/blob/main/corne-classic/doc/buildguide_en.md)
-
Help needed regarding handwireing
I would need hex file from here https://github.com/foostan/crkbd/blob/main/doc/firmware_en.md and then i need to run flash command . Il read through it one more time, it seems that i use same hex file for both sides.
cantor
-
Corne, but with a wider thumb cluster and stronger column stagger?
There are a few things that are close: * The Cantor/Piantor: more aggressive stagger and slightly changed thumb cluster. * The Swept Corne: essentially a big sweep. * The Hillside 46/48: This comes in many forms which are very similar to what you are looking for. Essentially an extra aggressive stagger (and perhaps splayed) Corne with a bigger thumb cluster.
- With enough GPIO pins, can I skip diodes?
-
Cheapest way to try Miryoku style layout
Depending on how comfortable you are ordering PCBs yourself, the Cantor (https://github.com/diepala/cantor ) or the Cheapino (https://github.com/tompi/cheapino ) might be a good starting point for getting into split keyboards, both are diodeless, so you only need to solder the switches and use relatively cheap microcontrollers
-
My corne swept with handmade oak case
The Corne caught my eye first, but I ended up starting with a Cantor, which has more stagger, like OP's keyboard. It didn't work for me. The Corne works better for me.
- MRIYA
-
Optimising Colemak DH for Programming
cantor
-
What are the best designs to cheap out? E.g. Reviung34 only needs 1 controller.
Cantor by DiePala, Choc, diodeless, cheap “Black pill” mcu, requires two. Caseless/plateless. Pcb is reversible, but you’ll need trrs cable and Jack.
-
Adding millmax to non-swappable PCB
I have 2 hand-wired keyboards with cherry style switches, and I decided to build a Cantor (diodeless, Corne-like with more pinky stagger) to try a PCB build and the Kailh choc v1 switches for a first time.
-
Does the Lily58 have the same floating PCB problem of the Sofle?
several of the low-profile / Choc boards (ex. Cantor) go the plateless and caseless route with nothing more than rubber bumpers on the bottom of the PCB
-
How do I get started with KiCad for customizing an existing, open source layout?
Cantor – low profile
What are some alternatives?
dactyl-keyboard - Dactyl-ManuForm, a parameterized ergonomic keyboard
torn - Torn keyboard
SofleKeyboard - A split keyboard based on Lily58, Crkbd and Helix keyboards
piantor - The Piantor Keyboard is a beginner-friendly, easy-to-solder, 42-key or 36-key, diodeless, low profile aggressive column staggered, hotswappable and non-hotswappable, programmable ergonomic mechanical split keyboard powered by Raspberry Pi Pico or other compatible RP2040 boards. It is based on the Cantor Keyboard.
miryoku - Miryoku is an ergonomic, minimal, orthogonal, and universal keyboard layout.
zmk - ZMK Firmware Repository
Sweep - Sweep - a small promicro based keyboard inspired by the Ferris.
ErgoDash - keyboard
eternal-keypad - A 36 key gaming keypad, for both right and left handed mouse users.
fifi_split_keeb - Fifi Keyboard 🐶 ⌨️
cheapino