Voron-2
Voron 2 CoreXY 3D Printer design (by VoronDesign)
VoronUsers
Voron Community mods, slicer profiles and firmware configurations. (by dennistimmermann)
Voron-2 | VoronUsers | |
---|---|---|
88 | 3 | |
3,587 | 10 | |
2.0% | - | |
5.5 | 2.6 | |
2 months ago | over 2 years ago | |
GAP | ||
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Voron-2
Posts with mentions or reviews of Voron-2.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-05-14.
-
Newb with success!
Here's a link to a file.
-
V2.4 300mm CAD files?
What you're looking for would be the DXF cad files: https://github.com/VoronDesign/Voron-2/tree/Voron2.4/Drawing_DXFs/Panels
-
Planning to build my first printer
Here is a high contrast version of the 2.4R2 manual.
- Printer.cfg
- Silly question. How do you open bottom panel?
-
Ldo 2.4r2 rev c build - What are these parts for?
Page 246 and 285 of the Manual.
- Would you rather have a video assembly guide or written guide with pictures
-
What do you think of the Ankermake M5
Just a normal XYZ calibration cube would be cool. Or the Voron cube too.
-
Missing Part in 2.4r2 BOM (through Configurator)
I suppose that you could open a github issue? While you're there, it's worth reading through the other open issues in case you run into the same thing during your build.
- Anyone recognize this test print? Looking for the file..
VoronUsers
Posts with mentions or reviews of VoronUsers.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-09-16.
-
Probe comparison
I use a CR Touch with the CR Shell Mod and a modified MGN-12 SB carriage so that it fits in the stock probe slot. Started with unklicky-NG for a bit, but had too many issues with the dock flexing just enough during high temp prints that it wouldn't mount successfully unless I let everything cool down between prints.
-
How does one know what is the best configuration to build?
I went with the Stealthburner with CW2 instead of the AB with CW1. I also did CAN and went with the EBB36. I had planned to do the normal cable chains, but ended up switching to an umbilical for the extruder and chain for the Y (endstop board). I also did the AB Idler mod as I've seen a lot of people post problems with the stock one splitting at the tension bolt. I also did not use the stock induction sensor and went with a CR-Touch. The CR Touch mod does require a modifcation to the single MGN-12 carriage. I have my modified STLs/F3D files if you're interested. I had the klicky (unklicky) mod for a while but had issues with heat causing the gantry mount to shift ever so slightly where I had mounting problems when warm. I've got about 150 hours of printing on the CR touch so far with no issues. I also did the purge/wipe bucket as well. At some point, I will likely do the pin mod and change the umbilical mod to this one and relocate the X endstop the print carriage and Y endstop the A drive mount. I also swapped out the door hinges after a few hours.
-
Ender 3 V2.. need hotend recommendations.
I'm planning on using the Afterburner by Voron Design that is on their 2.4r2 build (STLs here), with this mod to allow me to still use my CR touch.
What are some alternatives?
When comparing Voron-2 and VoronUsers you can also consider the following projects:
Voron-Trident - Voron Trident CoreXY 3D Printer design
Voron-2-Mods - All my mods at one place
Micron
Voron - This repository contain files related to modifications or experimentations I performed on parts of 3D Printers designed by the Voron team
Voron-Afterburner - VORON Afterburner Upgrade
VoronMods - Mods I have created for my Voron printer
klipper - Klipper is a 3d-printer firmware
Stealthburner-Umbilical-mod
EnragedRabbitProject
VoronUsers - Voron Community mods
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
Voron-Hardware - Cool Hardware designed by the Voron Design group
Voron-2 vs Voron-Trident
VoronUsers vs Voron-2-Mods
Voron-2 vs Micron
VoronUsers vs Voron
Voron-2 vs Voron-Afterburner
VoronUsers vs VoronMods
Voron-2 vs klipper
VoronUsers vs Stealthburner-Umbilical-mod
Voron-2 vs EnragedRabbitProject
VoronUsers vs VoronUsers
Voron-2 vs klipper
Voron-2 vs Voron-Hardware