Sanguino VS Arduino

The first time I programmed my v1.1.4 board, I set up an Arduino Uno to use as the programmer, in ArduinoIDE 1.8.9. Then I used the board manager to install https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json to the "Additional Boards Manager URLs" field as per the instructions at https://github.com/Lauszus/Sanguino/tree/master, and installed the bootloader. That was in early 2019, and I didn't have any problems, but I believe that later versions of ArduinoIDE 2.x may be slightly different. Maybe worth trying an older version?

/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * Sanguinololu board pin assignments */ /** * Rev B 26 DEC 2016 * * 1) added pointer to a current Arduino IDE extension * 2) added support for M3, M4 & M5 spindle control commands * 3) added case light pin definition */ /** * A useable Arduino IDE extension (board manager) can be found at * https://github.com/Lauszus/Sanguino * * This extension has been tested on Arduino 1.6.12 & 1.8.0 * * Here's the JSON path: * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json * * When installing select 1.0.2 * * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino * Just use the above JSON URL instead of Sparkfun's JSON. * * Once installed select the Sanguino board and then select the CPU. */ #define ALLOW_MEGA644P #include "env_validate.h" #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "Sanguinololu <1.2" #endif // // Limit Switches // #define X_STOP_PIN 18 #define Y_STOP_PIN 19 #define Z_STOP_PIN 20 // // Steppers // #define X_STEP_PIN 15 #define X_DIR_PIN 21 #define Y_STEP_PIN 22 #define Y_DIR_PIN 23 #define Z_STEP_PIN 3 #define Z_DIR_PIN 2 #define E0_STEP_PIN 1 #define E0_DIR_PIN 0 // // Temperature Sensors // #define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) #define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) // // Heaters / Fans // #define HEATER_0_PIN 13 // (extruder) #if ENABLED(SANGUINOLOLU_V_1_2) #define HEATER_BED_PIN 12 // (bed) #define X_ENABLE_PIN 14 #define Y_ENABLE_PIN 14 #define Z_ENABLE_PIN 26 #define E0_ENABLE_PIN 14 #if !defined(FAN_PIN) && ENABLED(LCD_I2C_PANELOLU2) #define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan #endif #else #define HEATER_BED_PIN 14 // (bed) #define X_ENABLE_PIN 4 #define Y_ENABLE_PIN 4 #define Z_ENABLE_PIN 4 #define E0_ENABLE_PIN 4 #endif #if !defined(FAN_PIN) && (MB(AZTEEG_X1, STB_11) || IS_MELZI) #define FAN_PIN 4 // Works for Panelolu2 too #endif

Grab the Sanguino Board plugin here - https://github.com/Lauszus/sanguino/zipball/master and extract to Desktop

I believe it's the Sanguino 1284P. Have a look at the Github: https://github.com/Lauszus/Sanguino

I learned from looking at example code in the Arduino IDE (a really good and free code editor https://www.arduino.cc/en/software). The Arduino IDE allows you to add more boards (like ESP32, ESP8266, Tiny etc.) so you're not limited to using only their Arduino boards.

Based on what I am seeing from the Keystudio website, the software you need is just the Arduino IDE. This can be downloaded from Arduino.cc for most operating systems, including Mac OSX. You may need to install support for other boards or install libraries to make it work with the Arduino and hat included with the kit.

Download and install the Arduino IDE. After installation, open the IDE to the first sketch.

Well, your first course of action would be to download the software - https://www.arduino.cc/en/software

You can download the IDE from here.

You will need to download and install the Arduino IDE to do that. I would suggest the Legacy 1.8.x IDE or the Arduino Web Editor (which will still require that you install some software on your computer to help transfer the program to the Arduino).

The software used for that video is the arduino IDE https://www.arduino.cc/en/software

Wiring: You're on the right track with your wiring assumptions. The red wire should connect to the 5V pin, the black wire to the GND pin, and the green wire to one of the analog input pins (A0-A5) on the Arduino Leonardo. For example, you can connect the green wire to the A0 pin. Programming the Arduino Leonardo: To translate the handbrake input to Assetto Corsa, you'll need to program the Arduino Leonardo to act as a USB HID (Human Interface Device). This will allow your computer to recognize it as a game controller. First, you'll need to install the Arduino IDE (Integrated Development Environment) on your computer. You can download it from the official website: https://www.arduino.cc/en/software