MxLEDBitPCB VS su120-keyboard

I've tried the MXLEDBitPCB personally for a dactyl and it worked great. (I used the "Container" variant). My dactyl case holes were a tiny bit too big, but once i got the hotswap sockets in, it held the keys well enough to stop the wiggle. My only complaint is that the 5x5 PCB layout made it a pain to break them apart, and it left little fiberglass nubs i had to sand down. The labeling was a bit easier to understand than the Amoebas, but it also not as fancy. The big advantage these have, is they support through-hole diodes, as opposed to tiny smd diodes.

dometyl can generate keywells with hotswap socket slots, you can hot-glue/crazy-glue them in place or just yolo them in place. I prefer to use 1u pcb's, since soldering wire to them is much easier. The MxLEDBitPCB atlanta support hotswap sockets and you can have many manufactured very cheaply by jlcpcb.com.

These PCBs: https://github.com/swanmatch/MxLEDBitPCB/tree/master/container

MxLEDBitPCBs have a Choc variant, too: https://kbd.news/MXLEDBitPCB-1060.html

Also worth noting that Amoeba Royale has very small LED solder pads compared to mxledbit's "container" ( https://github.com/swanmatch/MxLEDBitPCB/tree/master/container ) board.

. The trouble? I got the Altana board made which only supports sk6812 mini LEDs (for an underglow I suppose) and do NOT support the sk6812 mini *-e* LEDs which tend to be the first result that come up if you just search sk6812 mini. See this wonderful github thread of another fellow keyboard enthusiast making the same mistake. In fairness the support rubric is pretty clear so I was just being stupid/hasty/whatever.

I much preferred the idea of SK6812MINI-E LEDs, but couldn't source a PCB that worked with chocs and also the MINI-Es. I decided to try handwiring one, then found the MxLEDBitPCB: the choc version supports MINI-Es, and it looked as if it might make handwiring a little more straightforward for a relative newbie.

It's per-switch using PCBs from this repo: https://github.com/swanmatch/MxLEDBitPCB

Hey all! I'm trying to put together a handwired dactyl build with hotswap and RGBs in each switch using the MxLEDBitPCB Amoeba.

MxLEDBitPCB altana from jlcpcb $6 with shipping - you may want to choose the container version if you want backlighting but the wiring if more involved so I did not go this route

They are SU120. There is a bug in the file that prevents JLCPCB from recognizing/producing them. (I've got a PR in to fix that). Elecrow is fine with it though.

The SU120. Hot swap only, but very clever design. Columns and rows are connected by default, so one only needs to connect the ones you break. The creator has made it available in git (link)

I'm using the su120 boards. They are snap-apart-optional single key pcbs that can be joined with screws rather than wires. (I'm sick of soldering Amoebas for dactyls). You can see them in the upper-left. They support hotswap sockets, rotary encoders, and can be a board by themseleves if you don't break them apart and solder on a pro-micro. I'm concerned about not finding an optimal connector length for the angled thumb pieces - but I'm not above a little bit of soldering now and then.

Isn’t the su 120 what you are looking for?

You can also use su120 for this. I made a magnetic adjustable layout tester keyboard using those.

Someone recently posted a dactyl build using these. https://github.com/e3w2q/su120-keyboard

A set of Dactyl Manuform 5x6 cases with 5-key thumb clusters and external PCB trays printed in clear PLA. Holes have undercut notches for cherry/compatible and small screw holes (M1.4x5 self-tapping screws) to fit SU120 PCBs per key. Comes with threaded inserts and screws for base plates.

I used SU120 bit boards (from /u/e3w2, thanks for open-sourcing it!) as a base, to which I added SK6812 mini-e support (had to remove support for choc sockets though).