Klicky-Probe
Microswitch probe with magnetic attachement, primarily aimed at CoreXY 3d printers (by jlas1)
KlackEnder-Probe
Klicky / Quickdraw Probe for the Ender 3 (by kevinakasam)
Klicky-Probe | KlackEnder-Probe | |
---|---|---|
69 | 28 | |
1,176 | 336 | |
- | - | |
5.0 | 5.4 | |
7 days ago | 5 days ago | |
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Klicky-Probe
Posts with mentions or reviews of Klicky-Probe.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-12-08.
- Voron Legacy Serial Request - u/Deadbob1978
- Voron 2.4 klicky probe issue
-
Using a servo on Creality 4.2.7
I used this github as a guide to get my servo to work on my BTT SKR Mini E3 V3 https://github.com/jlas1/Klicky-Probe/tree/main/Printers/Voron/Switchwire then you have to mess with the pulse width value until it works right, lots of trial and error
-
Controlling servo with E3V2 stock board
So you want to use this one? https://github.com/jlas1/Klicky-Probe/tree/main/Printers/Voron/Switchwire
-
Another Perfect First Layer
GitHub, there's the install for all the different variants (klicky, unklicky and the ng variants), with macros, boms and instructions https://github.com/jlas1/Klicky-Probe
-
Klicky probe config
I just went through the same build and I just included the klicky files as specified here, edited the variables file and that was it
- Unpopular opinion: ABL is trash
- Z-offset is constantly changing after every quad_gantry_level (v2.4)
- Ender 6 with SKR mini e3v3 and klipper ABL options
-
Motor to open V2.4 Doors
The official Klicky setup for the Switchwire uses one as well
KlackEnder-Probe
Posts with mentions or reviews of KlackEnder-Probe.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-04-20.
- Sick of Bed Leveling
- BLtouch or Klicky?
-
KlackEnder Ender prove on Aquila x2
Has anyone tried to put one of these https://github.com/kevinakasam/KlackEnder-Probe on an Aquila x2. Would it work? Will I need to change anything?
- Rate my first layer
- [Artillery 3D] Sidewinder x2
-
[USA][ABS] 4 pieces for KlackEnder
I'm hoping to find someone who would be willing to print the four files in this github repo (excluding the tolerance test) in ABS. Color does not matter to me. The total filament used should be about 14g, and minimum printer size required is 40x40x25mm.
-
Controlling servo with E3V2 stock board
check this out, should help https://github.com/kevinakasam/KlackEnder-Probe , also have you seen the klicky probe page on the switchwire github?
-
3d printable upgrades
KevinAkaSam's KlackEnder probe is awesome. I found it to be much more reliable than the BLTouch or CRTouch I'd had previously, and it's more fun to watch. You do need to be able to crimp connectors for a JST plug, but you don't need to solder anything. The fact that it uses electronics at all is kind of scary, but it's a good project if you're just beginning to explore integrating electronics with your builds.
-
Is this too fast? Settings in the comments.
Looks like this: https://github.com/kevinakasam/KlackEnder-Probe
-
hey is there a Klicky Probe for the cr-10 s/cr10 im poor for the cr touch
This one is designed for the ender 3 but should work great in the cr-10 as well https://github.com/kevinakasam/KlackEnder-Probe
What are some alternatives?
When comparing Klicky-Probe and KlackEnder-Probe you can also consider the following projects:
Euclid_Probe - Euclid probe, a magnetically coupled Z Probe
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
klipper_z_calibration - Klipper plugin for self-calibrating z-offset
BeltDrivenEnder3 - All parts including Voron files for the Belt Driven Ender 3 V3
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
SlideSwipe
whopping_Voron_mods
VoronUsers - Voron Community mods
Quickdraw_Probe - A Magnetically Coupled, Removable, Z Probe and Dock System
ZeroClick - ZeroClick - fast & simple bed probing for tiny printers
Voron-Afterburner - VORON Afterburner Upgrade
VoronUsers - Voron Community mods, slicer profiles and firmware configurations.
Klicky-Probe vs Euclid_Probe
KlackEnder-Probe vs VoronUsers
Klicky-Probe vs klipper_z_calibration
KlackEnder-Probe vs BeltDrivenEnder3
Klicky-Probe vs VoronUsers
Klicky-Probe vs SlideSwipe
Klicky-Probe vs whopping_Voron_mods
Klicky-Probe vs VoronUsers
Klicky-Probe vs Quickdraw_Probe
Klicky-Probe vs ZeroClick
Klicky-Probe vs Voron-Afterburner
Klicky-Probe vs VoronUsers