.emacs.d VS doom-emacs

Yesterday, I was debugging my configuration because of increased init time (0.5-0.8 seconds), then I realized by a coincidence that if I load straight/bootstrap.el manually, and open a new Emacs instance immediately, it starts much more quick (~%65). It is related native comp I guess but I actually still cannot find the reason for this. I checked out the source code of straight.el, spent 4-5 hours and find out that a find process with all the packages I installed as args takes ~1.5 seconds to finish. I disabled it in source code and my startup time decreased from ~2.3s to 0.8s.

source code: https://github.com/KaratasFurkan/.emacs.d#zoom

You can get ideas from init.el, early-init.el and Applying Changes sections of my literate configuration. They are about loading config and keeping org and elisp files synced.

$ rm -rf ~/.config/emacs # Remove the existing directory if necessary git clone --depth 1 https://github.com/hlissner/doom-emacs ~/.config/emacs ~/.config/emacs/bin/doom install

Sounds like what you want is emacs, but preconfigured. In that case, have you tried Doom Emacs, Spacemacs or any of the myriad of others like those?

darren@pop-os:~$ git clone --depth 1 https://github.com/hlissner/doom-emacs ~/.emacs.d Cloning into '/home/darren/.emacs.d'... remote: Enumerating objects: 1156, done. remote: Counting objects: 100% (1156/1156), done. remote: Compressing objects: 100% (1042/1042), done. remote: Total 1156 (delta 85), reused 650 (delta 71), pack-reused 0 Receiving objects: 100% (1156/1156), 1.13 MiB | 7.29 MiB/s, done. Resolving deltas: 100% (85/85), done.

I used to do something like -{ nixosConfig, config, lib, pkgs, ... }: -let - xdgConfig = config.xdg.configHome; -in { - home.activation = { - foo = lib.hm.dag.entryAfter [ "writeBoundary" ] '' - doomdir="${xdgConfig}/doom"; - # $VERBOSE_ARG - if [ -d "$doomdir" ]; then - $DRY_RUN_CMD git -C "$doomdir" pull http master || true - else - # git clone and change url - http="https://git." - $DRY_RUN_CMD git clone "$http" "$doomdir" - # the new url needs ssh keys setup - git -C "$doomdir" remote add http "$http" - git -C "$doomdir" remote set-url origin "gitea@git." - fi - emacsdir="${xdgConfig}/emacs" - if [ -d "$emacsdir" ]; then - if [ -d "$emacsdir/.local" ]; then - $DRY_RUN_CMD $emacsdir/bin/doom sync - fi - else - $DRY_RUN_CMD git clone --depth 1 https://github.com/hlissner/doom-emacs "$emacsdir" - fi - ''; - }; -}

`;; Needed to add javascript-eslint to the the next-checker after lsp so that it would actually load, as that wasn’t happening by deafult ;; also needed to runit after the lsp-afer-initalize-hook because otherwise ‘lsp wasn’t a valid checker (add-hook ‘lsp-after-initialize-hook (lambda () (flycheck-add-next-checker ‘lsp ‘javascript-eslint))) ;; https://github.com/hlissner/doom-emacs/issues/1530 ;; Potential alternative to the above ;; (after! (:and lsp-mode flycheck) ;; (flycheck-add-next-checker ‘lsp ‘javascript-eslint))

The performance lag of Spacemacs was addressed by Doom Emacs ( https://github.com/hlissner/doom-emacs ). Have you tried Doom Emacs by any chance. After syncing everything, the performance is stellar in my opinion.

but I just realized, you're probably better off using doom emacs. The defaults are sane, customizations are almost always optional and the community's really active/helpful. (Disclaimer: I'm a doom emacs user with ~2k lines of config)

While Doom is more opinionated, it's not too difficult make Emacs your own, most of the choices are optimized anyway. Currently the head of Spacemacs devs is not active on the project anymore. Also I don't think it's hard to upstream code to Doom, as long as the code is thoroughly written, take a similar example on both sides: the introduction of a completion engine as layer/module (same packages are installed): - https://github.com/syl20bnr/spacemacs/pull/14901: 23 comments, 7 participants - https://github.com/hlissner/doom-emacs/pull/4664: 576 comments, 20 participants

Also Doom emacs has one. https://github.com/hlissner/doom-emacs https://github.com/hlissner/doom-emacs/tree/master/modules/lang/common-lisp

Nowadays, I use https://github.com/hlissner/doom-emacs with WSL2 but only for org-mode. For code, I have either Sublime Text or VS Code.