BIGTREETECH-OCTOPUS-V1.0
This is Octopus open source material (by bigtreetech)
tronxy-x5sa
Tronxy X5SA Pro Klipper configuration (by markcarroll)
BIGTREETECH-OCTOPUS-V1.0 | tronxy-x5sa | |
---|---|---|
44 | 1 | |
536 | 10 | |
- | - | |
4.7 | 0.0 | |
4 months ago | about 2 years ago | |
C | ||
- | - |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
BIGTREETECH-OCTOPUS-V1.0
Posts with mentions or reviews of BIGTREETECH-OCTOPUS-V1.0.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-01-31.
- Big Tree tech Board firmware
-
Cannot access serial/by-id in my Octopus Pro
It is strange though that the firmware I've built has a size of 28kb, while the one you can download from the BTT repo is only 23kb. Both can be flashed, but neither of them seems to work.
-
TAP- V2.4r Octopus v1.1- probe ports pin out.
https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/tree/master/Hardware/BIGTREETECH Octopus - PIN.pdf
-
Klipper ls cannot access /dev/serial/by-id/* No such file or directory
just checking, have you tried the precompiled firmware from bigtreetech? https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/tree/master/Firmware
-
Migrating from inductive probe to Tap on an Octopus v1.1
I have a 4.7kΩ pull up resistor soldered between 24VDC and PB7 (probe pin) on my board. This is detailed on page 11 of the user manual here (github).
-
Help Setting Up Nema 14 for Stealthburner
See the manual for that board here which outlines the different jumper configurations
- Help wiring BTT octopus 1.1 board replacement! Is there an online tutorial?
-
BIGTREETECH-OCTOPUS-V1.0 VS MKS-Monster8 - a user suggested alternative
2 projects | 31 Jan 2023
-
neoplixel wiring with hartk stealthburner board(single)
I followed this wiring pinout and wired my neopixels following this: https://imgur.com/a/TtQbZPe. They are not currently working. The pin referenced on the pinout in the picture references the PB0 pin on the Octopus board as seen here: https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/blob/master/BIGTREETECH_Octopus_EN_updated_0719.pdf
-
Another BTT OCTOPUS PRO short... any chance of repair?
With care and patience you can do it with a good quality soldering iron. You'll need solder wick to remove the old solder and good flux to fit replacement parts. You can use ordinary electronics grade tin/lead slder for the replacements; it's easier to use than lead-free, which is only mandated for commercial products for sale. As usual for BTT products, the schematic and other documentation are on BigTreeTech's github, https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/tree/master/Hardware
tronxy-x5sa
Posts with mentions or reviews of tronxy-x5sa.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2021-11-13.
-
Have you swapped your X5SA factory board for a Spider or Octopus? Can you please tell me what steps/issues were involved?
here is my config so far: https://github.com/markcarroll/tronxy-x5sa
What are some alternatives?
When comparing BIGTREETECH-OCTOPUS-V1.0 and tronxy-x5sa you can also consider the following projects:
Voron-Trident - Voron Trident CoreXY 3D Printer design
klipper - Klipper is a 3d-printer firmware
FYSETC-SPIDER - FYSETC Board - 3d printer motherboard for VORON and other open source project.
katapult - Configurable bootloader for Klipper
MKS-Monster8 - MKS Monster8 is an 8-axis motherboard, which supports Voron printers and can run Marlin and Klipper firmware.
SKR-Pico