8812au-20210629 VS rtl8188eus

I've been trying for a few hours now to install drivers for a rtl8812au based usb wifi adapter (Edimax-7822ULC/UTC) on a nanopi r6c running kernel version 5.10.110. Zero luck with both the manufacturer driver for ubuntu and with an open source one-size-fits-all (https://github.com/morrownr/8812au-20210629). When running the manual install for morrownr's open source driver, I'm getting this error:

Is this a non-standart kali vm? If yes and you are learning, never sudo apt update/upgrade unless specifically told by your instructor. The adapter works for me with the drivers and intructions on github link

I have a dongle with that chipset, used it couple of times, worked fine. The driver I used is from here https://github.com/morrownr/8812au-20210629

Unofficially, the chipset itself seems to be the Realtek RTL8812AU chipset, which does have community support up to the current 6.1 kernel, but latest tested on Fedora is 5.11. (it will probably work, but honestly it's still a gamble). The work seems to mostly spur from the AUR repository, which links here.

As seen in the picture, every other ping seems to be about one second long and every other somewhat it should be. Pinging directly my Router via WLAN. There are different drivers available for the RTL8812AU, currently using this one: github.com/morrownr/8812au-20210629. The same issue persists using other drivers available. Power saving settings for the adapter are turned off, no effect.

The driver is available on github.

git clone https://github.com/morrownr/8812au-20210629.git

I had to reinstall a newer version of my driver ---> https://github.com/morrownr/8812au-20210629/issues/67

First you will need to find out which version you have. Version one or two (this one) will need this driver. For version three (this one) you will need this driver.

I am a bit new to using Linux (almost) full time. I am trying to get my USB WiFi dongle to work on my M1 MBA. I am on Asahi's Edge branch and cannot seem to find the headers needed to build the drivers found here (aircrack-ng). Please tell me how I am being stupid.

I have Archer T2U Nano and I got it working in Linux by getting the rtl8821au driver from github. From my short time Googling I find that yours is rtl8812au, so if you want to try you could check that out. There's one for rtl8812 here.

net-wireless/rtl8192eu::guru Realtek 8192EU driver module for Linux kernel (https://github.com/Mange/rtl8192eu-linux-driver) net-wireless/rtl8821ce::guru Realtek RTL8821CE Driver module for Linux kernel (https://github.com/tomaspinho/rtl8821ce) net-wireless/rtl8821cu::guru Realtek 8821CU/RTL8811CU module for Linux kernel (https://github.com/brektrou/rtl8821CU) net-wireless/rtl8812au::pentoo Driver for the ASUS USB AC56 (801.11ac) wireless adapter (http://www.asus.com/Networking/USBAC56/) net-wireless/rtl8812au_aircrack-ng::pentoo RTL8812AU/21AU and RTL8814AU driver with monitor mode and frame injection (https://github.com/aircrack-ng/rtl8812au) net-wireless/rtl8822bu::pentoo RTL88x2BU driver with monitor mode and frame injection (https://github.com/EntropicEffect/rtl8822bu.git)

The driver I was using is the following https://github.com/aircrack-ng/rtl8812au

https://github.com/aircrack-ng/rtl8812au https://github.com/morrownr/8812au (does not contain code, but a link to the most recent driver)

I found a github repo (https://github.com/aircrack-ng/rtl8812au) which seemed to have support for the rtl8812au driver that the A6100 uses, but when trying to install it, I got an error that DKMS couldn't find a binary. Does this have something to do with the fact that I am booting in live mode with a flash drive? I want to make sure that my hardware works before installing.

(rtl8812/11au drivers: https://github.com/greearb/rtl8812AU_8821AU_linux#makefile--for-instance-this-builds-against-recent-openwrt-neo2-platform--your , https://github.com/aircrack-ng/rtl8812au)

Fair warning here that this didn't work for me and it took ~5h to reach a solution for kali after many many forum posts, almost the same adapter, but should be the same process. Basically, follow this github if the solution above doesn't work. https://github.com/aircrack-ng/rtl8812au