0xCB-1337
Mechanical macropad with OLED running QMK (by 0xCB-dev)
Repetier-Firmware-4-Davinci
Repetier-Firmware-0.92 based for DaVinci printer (Beta - so far so good) (by luc-github)
0xCB-1337 | Repetier-Firmware-4-Davinci | |
---|---|---|
2 | 5 | |
51 | 191 | |
- | - | |
4.1 | 3.5 | |
11 months ago | 8 months ago | |
HTML | HTML | |
GNU General Public License v3.0 or later | GNU General Public License v3.0 only |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
0xCB-1337
Posts with mentions or reviews of 0xCB-1337.
We have used some of these posts to build our list of alternatives
and similar projects.
-
[Artisan] PunchType/ Ghost Encoder Knobs
The macropod is from 0xCB we had a collaboration with them. I think these will be out soon. I did manage to get my hands one absolutely love it.
-
You guys wanted it - here it is :D - back in stock
Github: https://github.com/Conor-Burns/0xcb-1337
Repetier-Firmware-4-Davinci
Posts with mentions or reviews of Repetier-Firmware-4-Davinci.
We have used some of these posts to build our list of alternatives
and similar projects.
-
Davinci 1.0a Extruder and Bed Not Heating Up
I have a Davinci 1.0a with Repetier 0.92.10 installed via the tutorial from Luc (https://github.com/luc-github/Repetier-Firmware-4-Davinci). Everything appears to function properly but the hot end and bed won't heat up nor is voltage being sent to them. I've pulled the plugs to the power supply and tested everything, it seems normal. I've checked fuse R271 and have continuity through it. I have a 4gb ADATA microSD so storage shouldn't be an issue. Do I need to change something in the configuration file for Repetier or should everything just work? What are some other points on the mainboard to check to help narrow down the issue?
-
XYZ Da Vinci Du0
Github link
-
Fixing broken USB in 3D printer (ATSAM3X8EA-AU / Arduino bootloader)
I've had an XYZ DaVinci 1.0A for a couple of years now, flashed with custom Repetier firmware and connected to OctoPi / OctoPrint. It worked fine, until a couple of month ago the USB connection started getting flaky and I needed to power-cycle the printer to get USB back. Now USB disappeared completely. The printer apparently still runs its firmware (it shows its menu on the LCD when turned on), but there's to USB connection to the Pi. Plugging the printer into a different computer shows no USB device / only USB errors in Linux dmesg. I've tried resetting the firmware via J37 which should put it into firmware upload mode (acting as an Arduino board), but still nothing. I used an oscilloscope to check and there's activity on the D+/D- lines, so the cable is good, but the printer mainboard isn't responding. I suspect the Atmel ATSAM3X8EA-AU that provides the USB to be broken (at least the USB part). I could change the chip, but am unsure if / how I can flash the blank chip with the new firmware (an Arduino bootloader?). If you have ideas what else I should check or clarify the firmware situation I'd be grateful! If you need mainboard images, tell me. I have no schematics though...
-
Bed doesn’t travel down - Repetier .92
Ok, let's start with the beginning... Before you flashed Repetier did it print and function normally? Next did you get the correct version of .92 , I think there are 2 or 3 different boards that require different versions. If you check this out https://www.thingiverse.com/groups/xyz-davinci-10/forums/general/topic:823 and this https://github.com/luc-github/Repetier-Firmware-4-Davinci. It should help, follow the procedure on thingiverse and re-flash with the binary from the github. let me know if it works after that. My 1.0 took a couple of tries and I had to send the M503 and M500 commands from pronterface to get it to start.
- I'm having cooling issues with my prints, so I decided to print a mount for a new cooling fan. But that print also had cooling issues. Enter solution:
What are some alternatives?
When comparing 0xCB-1337 and Repetier-Firmware-4-Davinci you can also consider the following projects:
FG-Falcon - FoA Orion Repository
ESP3D - FW for ESP8266/ESP8285/ESP32 used with 3D printer
Awesome-Keebs - A collection of keyboards & things.
prettier - Prettier is an opinionated code formatter.
install - Tasmota Web Installer and firmware repository
x11docker - Run GUI applications and desktops in docker and podman containers. Focus on security.
NOMI-VR - NOMI VR Is An Inexpensive, Steam VR Compatible, Open Source VR Headset With Finger Tracking, Haptic Gloves.
0xCB-1337 vs FG-Falcon
Repetier-Firmware-4-Davinci vs ESP3D
Repetier-Firmware-4-Davinci vs Awesome-Keebs
Repetier-Firmware-4-Davinci vs prettier
Repetier-Firmware-4-Davinci vs install
Repetier-Firmware-4-Davinci vs FG-Falcon
Repetier-Firmware-4-Davinci vs x11docker
Repetier-Firmware-4-Davinci vs NOMI-VR