VoronUsers VS Voron-Hardware

Z-Drive Motor Tensioner Mod https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/edwardyeeks/V2.4_z_drive_motor_tensioner_mod ————— Pins Mod https://github.com/hartk1213/MISC/tree/main/Voron%20Mods/Voron%202/2.4/Voron2.4_Pins_Mod ————— GE5C Mod https://github.com/hartk1213/MISC/tree/main/Voron%20Mods/Voron%202/2.4/Voron2.4_GE5C ————— MGM12H Mod https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/arkeet/mgn12 ————— Extrusion Backers https://github.com/tanaes/whopping_Voron_mods/tree/main/extrusion_backers ————— LGX Extruder https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/geoffreyyoung/lgx https://www.teamfdm.com/files/file/381-afterburner-lgx/ ————— Alternative Front Idlers https://github.com/Ramalama2/Voron-2-Mods/tree/main/Front_Idlers ————— Hall Sensor Endstop https://docs.vorondesign.com/community/electronics/120decibell/hall_effect_endstop_setup.html https://github.com/VoronDesign/Voron-Hardware/tree/master/Hall_Effect_XY_Endstop ————— Voron Logo https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/GadgetAngel/Cricut_Voron_Logos ————— Klicky-Probe (also used as virtual endstop) https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/JosAr/Klicky-Probe ————— Nevermore Micro Filter https://github.com/0ndsk4/VoronUsers/tree/0ndsk4/printer_mods/0ndsk4/Nevermore_Air_Filter/Nevermore_Micro ————— Stealthburner (SB Beta 3, Dragon Beta 1) https://github.com/VoronDesign/Voron-Afterburner/tree/sb-beta/STLs/Stealthburner ————— 270° Door hinges https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/chrisrgonzales/270_degree_hinge ————— No Exhaust Back Plate https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/richardjm/back-plate ————— LED Bar Clip https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/eddie/LED_Bar_Clip —————

As for VOCs, even PLA releases them. A popular mod have been the Nevermore, a recirculating air filtration system that uses activated charcoal to eliminate a great deal of the VOC released during printing. There are many sizes, the most popular is the Nevermore Micro: https://github.com/0ndsk4/VoronUsers/tree/0ndsk4/printer_mods/0ndsk4/Nevermore_Air_Filter/Nevermore_Micro

Here's the GitHub for the mod if you want more info.

That's the Nevermore Micro recirculating air filter, https://github.com/0ndsk4/VoronUsers/tree/0ndsk4/printer_mods/0ndsk4/Nevermore_Air_Filter/Nevermore_Micro . It uses two fans and a small bucket of activated charcoal for effective and cheap filtering of the VOCs and odor given out when printing ABS etc. It is very effective in heating up the build chamber as well.

Maybe it works ok with caulk + internal HEPA, f.x. Nevermore micro and exhaust to the outside at the end.

Hello, the toolhead wiring may require few finishing touches. Ziptie those wires as close to the toolhead as possible, or use a wiring cover. If the stock one is small, you can use some of these for toolhead PCBs which are larger. https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs/Clockwork/Covers

That would be this one https://github.com/VoronDesign/Voron-Hardware/tree/master/V0-Umbilical/

I'm trying to setup the V0 display on my V0.2 but I get an error when trying to flash klipper to it. I'm following this guide and it shows up correctly with 'lsusb' but at step 9 it gives me this error. Can anyone tell me what I'm doing wrong? I'm using the BTT Pi V1.2 and an SKR Pico.

Hello, please, is there any chance to tidy up the wiring on Afterburner toolhead a bit? I believe there should be a shorter standoff available for Afterburner toolhead PCB, and the PCB cover can be found here https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover or here https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs

Hello, the toolhead wiring could use few finishing touches ... any chance you could ziptie those wires a bit closer to the toolhead, or ven better put a wiring cover? If the default one is small, you can use for example this one for toolhead PCBs but it works well for Microfit connectors too https://github.com/craxoor/VoronMods/tree/master/PCB%20Cover or https://github.com/VoronDesign/Voron-Hardware/tree/master/Afterburner_Toolhead_PCB/STLs/Clockwork/Covers

Hi, yes you can as stated earlier by u/rgar132 Alternatively you can also get Klipper Expander, it's a small MCU which will provide few more connectors for various purposes. https://github.com/VoronDesign/Voron-Hardware/tree/master/Klipper_Expander I got mine from Ali if you do not have option to have it made by PCB manufacturer, but I am sure few vendors have those as well.

Firstly, on the guide: https://github.com/VoronDesign/Voron-Hardware/tree/master/Daylight it mentions that the sticks need 24v but on the PCB's it says that they are 5v (https://imgur.com/a/cl4vzjY) and im not sure what to go for here.

The toolhead wiring requires some finishing touches too. Ziptie those stray wires to the rest of the bundle, or hide those under cable cover. If the stock is too small, use one of the larger alternatives like this one or some of these.