SKR-Pico
By bigtreetech
klipper_configs
By ajventer
SKR-Pico | klipper_configs | |
---|---|---|
13 | 5 | |
172 | 0 | |
- | - | |
0.0 | 5.5 | |
over 1 year ago | 5 months ago | |
- | - |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
SKR-Pico
Posts with mentions or reviews of SKR-Pico.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-05-20.
-
Where to get a 20A SMD fuse quickly (US - Florida)
That's a question outside my scope of knowledge. I can tell you that it's a microcontroller used to control a 3D printer. There are 5 NEMA 17 stepper motors, a hot end for melting and extruding the filament (around 200 Celsius) and the build plate is heated (60 - 70 Celsius). Here is a link to the manufacturer's GitHub if you're interested in checking it out: https://github.com/bigtreetech/SKR-Pico/tree/master/Hardware
- V0.2 won't connect to Mainsail without hitting the reset buttons
-
skr 3 ez: does pyserial work or flash manually?
https://github.com/bigtreetech/SKR-Pico/blob/master/Klipper/Images/wiring_uart.png they have the wires backwards.... I see a lot of things like that. That's just different from what is shipped. Forget about the fact that the wire is plugged in backwards, what is shipped to the customer is two reds, a black, one green and one yellow. There is no blue. That's what I feel like right now: I'm following instructions/directions with a blue wire and there was no blue wire in the box...
-
SKR Pico With Sonic Pad? Anyone have success?
I have a sonic pad that I have working on one printer that uses an aquila motherboard so I know the sonic pad works. I just got an SKR Pico and installed it in a different printer. I flashed the firmware and with klipper-USB.uf2 from https://github.com/bigtreetech/SKR-Pico/blob/master/Klipper/README.md
-
SKR Pico: no communication
Did you go through the steps here for building the firmware? https://github.com/bigtreetech/SKR-Pico/blob/master/Klipper/README.md
-
mobo upgrade incoming, please help.
The SKR-Pico is very well-documented on the BigTreeTech github page
-
Power specs on SKR Pico?
I'm looking around for specs on maximum power/current draw for the SKR Pico run at 24V. Unfortunately, the documentation is pretty slim (link to BTT Github for SKR Pico), only mentioning 0.8A draw on the stepper drivers without additional cooling in the user manual. I'm concerned that the board may not be capable of pulling enough power for my Gulf Coast Robotics heated bed, which lists a rating of 250W @ 24V (nearly 10.5A). I also have a Mosquito hot end, which lists a 50W heater, plus the motors drawing a total of over 40W, so I'm likely pulling over 350W, with running my SKR Pico, Pi Zero 2W, and touchscreen off the same PSU. (Pi and touchscreen were powered via UART cable off the Pico.)
-
MCU Lost Connection
Switching over your config should be pretty straightforward, you'll just be changing the [mcu] section (obviously) and all the pin assignments. BigTreeTech boards are really well-documented and both the SKR-Mini and the SKR-Pico include excellent pinouts and schematics as well as sample Klipper configs on their github pages.
-
Powering Le Potato (Libre AML-S905X-CC) with Octopus Pro or SKR Pico
Has anyone powered that board (Le Potato AML-S905X-CC-V1.0-A) by applying +5vdc to GPIO pins #2 and #4 (and ground to pin #6) as described by BTT here or page 10 of the BTT Octopus manual here?
- Voron 0.1 serial request spasticnerd97#3762
klipper_configs
Posts with mentions or reviews of klipper_configs.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2022-12-03.
What are some alternatives?
When comparing SKR-Pico and klipper_configs you can also consider the following projects:
BIGTREETECH-OCTOPUS-V1.0 - This is Octopus open source material
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
klipper - Klipper is a 3d-printer firmware
3DP-Build-Log - Build logs and notes about 3D Printers