Voron-Trident
Voron Trident CoreXY 3D Printer design (by VoronDesign)
tronxy-x5sa
Tronxy X5SA Pro Klipper configuration (by markcarroll)
Voron-Trident | tronxy-x5sa | |
---|---|---|
25 | 1 | |
568 | 12 | |
4.0% | - | |
5.6 | 0.0 | |
5 days ago | over 2 years ago | |
- | - |
The number of mentions indicates the total number of mentions that we've tracked plus the number of user suggested alternatives.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Voron-Trident
Posts with mentions or reviews of Voron-Trident.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2023-05-16.
-
Potential new Voron user
I like to use KIAUH to install Klipper on the host. The Klipper documentation has instructions on making and flashing the part that comes on the MCU. And the Voron GitHub has sample configs you can use to get started.
-
Serial Request - LDO Trident 300mm - H4kunaMatata#5589
If I can recommend - secure those wires when they exit X chain, else they will break in chains. print this https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Gantry/chain_wire_anchor_3hole_x2.stl put it under the chain end piece and use ziptie to tie wires to it. also, the Y cable bridge has a channel where you can put those wires into it, and secure them with zipties. Do not leave them strained like this.
-
serial request - voron trident 350mm - Hylton#2756
Any chance you could tuck the wiring of A and B motors to 2020 slot and use slot cover, or few of these clips? https://www.thingiverse.com/thing:2246832 or just stock ziptie anchor points https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl It will look a bit better IMO.
-
V2.4r2 Serial Request - Stevan#0496
Hello, I am not sure what's going on with your back if the gantry wiring. Can you tuck those wires in 2020 extrusion, and secure those with these little clips or print few of these anchors and use zipties? It will move them out of the way, decreasing risk of them getting caught into something. All wires on flying gantry go to A motor mount wnd then they enter Z chain -> to electronics compartment.
- Trident LDO Kit - Trouble squaring frame. What am I doing wrong?
-
Serial request V2.4r2 300mm Discord: Austenite#5308
Another one - ziptie your wires where they enter drag chains. You can print one of these and put under drag chain end when plastic part does not have holes for pulling zipties through: https://github.com/VoronDesign/Voron-Trident/tree/main/STLs/Gantry Tie it down on one side, then push wires from other side of the chain, pull them, and try to find some middle point between where they move in chain. Then ziptie it there. This will ensure they are not moving around in chains, which will cause them rubbing, and possibly breaking when they bunch up or tangle.
-
Serial Request - Voron Trident - alexmay#7047
There's a model for holding Wagos on bed extrusion https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Z_Assembly/wago_221-412_mount.stl
-
Serial Request - Voron 2.4 300mm - Shau Chen#1646
for the wiring goind from left B motor on gantry, you can tuck the cable in the 2020 extrusion groove and secure it with something like this https://www.thingiverse.com/thing:2246832 This clip from Trident repo https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl is also pretty useful to ziptie wires around the frame, inside electronics compartment for example.
-
Voron V2.4 350mm Serial Request LostG#1920
No problem, yeah bad luck that you just ran out of connectors :-) Maybe just print few of these https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl and tie the cables down on the bottom of crossbeam for now.
-
Voron Trident Serial Request AnonymousAsian#9857 (discord)
Looks OK, but I am not sure what's going on with cables on the right side around A motor. Any chance you could tuck them under 2020 profile cover or ziptie them? You can print a few of there https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl or https://www.thingiverse.com/thing:2246832
tronxy-x5sa
Posts with mentions or reviews of tronxy-x5sa.
We have used some of these posts to build our list of alternatives
and similar projects. The last one was on 2021-11-13.
-
Have you swapped your X5SA factory board for a Spider or Octopus? Can you please tell me what steps/issues were involved?
here is my config so far: https://github.com/markcarroll/tronxy-x5sa
What are some alternatives?
When comparing Voron-Trident and tronxy-x5sa you can also consider the following projects:
Voron-2 - Voron 2 CoreXY 3D Printer design
BIGTREETECH-OCTOPUS-V1.0 - This is Octopus open source material
klipper - Klipper is a 3d-printer firmware
VoronUsers - Voron Community mods
voron-parts - Just some other custom parts I've made that probably aren't worth making a pull request over
Voron-Hardware - Cool Hardware designed by the Voron Design group
Voron-Hardware - Cool Hardware designed by the Voron Design group