klipper

Klipper is a 3d-printer firmware (by KevinOConnor)
C

Klipper Alternatives

Similar projects and alternatives to klipper
NOTE: The number of mentions on this list indicates mentions on common posts. Hence, a higher number means a better alternative or higher similarity.

Posts

Posts where klipper has been mentioned. We have used some of these posts to build our list of alternatives and similar projects.
  • G code to reset Z offset?
    reddit.com/r/klippers | 2021-01-17
    Oh boy, I just went through what you're going through. Use SET_GCODE_OFFSET Z=0.2. The docs are here. It looks like the command is cumulative so if you sent 0.2 then 0.3 then it will be 0.5 not 0.3.
  • Bounty: $100 if you can help me fix my printers noise issue (Details in comments)
    A more precise approach is explained here even though there is more tinkering and extra hardware involved.
  • BLTouch Creality 4.2.7 Board
    reddit.com/r/klippers | 2021-01-13
    It's a little more work than it sounds: https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#how-do-i-convert-a-marlin-pin-number-to-a-klipper-pin-name
  • I finally got fluiddpi setup on my Ender 5 Pro (V1.1.5) + BLTouch - Any advice on printer limits etc? Prints look great so far!
    reddit.com/r/ender5 | 2021-01-13
    I found most of the documentation here: https://github.com/KevinOConnor/klipper/tree/master/docs
    reddit.com/r/ender5 | 2021-01-13
    u/EatMoTacos my config is based off the standard Ender 5 config from here: https://github.com/KevinOConnor/klipper/tree/master/config
  • Is there a way to tell is TMC2209 skipped steps after a print?
    reddit.com/r/klippers | 2021-01-11
    The FAQ describes how to use GET_POSITION to do this.
    reddit.com/r/klippers | 2021-01-11
  • Heatbed turned off when print is paused
    reddit.com/r/klippers | 2021-01-11
    https://github.com/KevinOConnor/klipper/blob/master/docs/Config_Reference.md#idle_timeout
  • Best firmware? 1.1.9 or 2.0.61?
    Best for stock MKS GEN L: Klipper https://github.com/KevinOConnor/klipper
  • Big Over-extrusion after Klipper install on Pi4 w SKR MiniE3 V2 and Ender 3 Pro
    reddit.com/r/klippers | 2021-01-03
    The latest config changes you can find here: https://github.com/KevinOConnor/klipper/blob/master/docs/Config_Changes.md
  • I have no idea why this is happening please help..
    Also, your nozzle is too far from the bed, so it's not adhering properly. If you're using Marlin run G29 (https://marlinfw.org/docs/gcode/G029-mbl.html) to run the paper test. On Klipper it's BED_SCREWS_ADJUST (https://github.com/KevinOConnor/klipper/blob/master/docs/Manual_Level.md).
  • Multiprinter Klipper Mainsail How To
    reddit.com/r/klippers | 2020-12-29
    https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#can-i-run-multiple-instances-of-klipper-on-the-same-host-machine
  • Biqu B1 with klipper
    reddit.com/r/klippers | 2020-12-26
  • Klipper Resonance Compensation ( input shape ) does not make any effect
    reddit.com/r/klippers | 2020-12-25
    Have you read https://github.com/KevinOConnor/klipper/blob/master/docs/Slicers.md ?
  • Step-by-Step Guide for Ender 3 v2 Klipper w/ BLTouch
    reddit.com/r/klippers | 2020-12-23
    i have 4.2.2 board on my 3 pro. There is an example config for it in the klipper github. https://github.com/KevinOConnor/klipper/blob/master/config/printer-creality-ender3pro-2020.cfg

Stats

Basic klipper repo stats
16
2,537
9.5
7 days ago

KevinOConnor/klipper is an open source project licensed under GNU General Public License v3.0 only which is an OSI approved license.